19 Cubic Yards of Gravel in Tons
19 cubic yards of gravel in tons works out to about 26.6 tons using a planning weight of 1.4 tons per yard. Real loads land between roughly 24.7 and 28.5 tons depending on stone size, fines and moisture. That is about 53,200 pounds.
Volume and tonnage calculator →The conversion
- Yards × tons per yard: 19 × 1.4 = 26.6 tons.
- Low end: 19 × 1.3 = 24.7 tons.
- High end: 19 × 1.5 = 28.5 tons.
Quarries can tell you the weight per yard for their own product; use it if you have it.
What 19 yards covers
| Depth | Square feet |
|---|---|
| 2 in | 3,078 |
| 3 in | 2,052 |
| 4 in | 1,539 |
| 6 in | 1,026 |
About gravel
Plain gravel is a loose term. Yards use it for rounded bank or river stone as well as for crushed rock, so ask whether the load is washed, crushed or a mix before you lock in a tonnage.
Hauling 19 yards
At about 26.6 tons, this is more than one typical truckload. A pickup is a poor fit for anything past a fraction of a yard; see how much gravel a half-ton pickup can carry.
Before you order
- Confirm whether the yard prices gravel by the ton or by the yard.
- Add about 10 percent for compaction and uneven ground.
- Clear a firm spot for the truck to dump.
The volume and tonnage calculator converts any area and depth into yards and tons.
Good and poor uses for gravel
Best suited to:
- Rural driveways and lanes where low upfront cost matters
- Drainage areas and around downspouts
- Temporary access while a site is under construction
Think twice for:
- Steep slopes, where loose stone washes downhill
- Spots plowed often, since plows push gravel into the lawn
- Areas next to doors, because stone tracks inside
Quick reference numbers
- Per inch over 100 sq ft: about 0.43 tons of gravel (0.31 cubic yards).
- Per inch over 1,000 sq ft: about 4.3 tons.
- Another size for comparison: a 12x24 area at 4 inches takes about 5.0 tons.
- Weight used here: about 1.4 tons per cubic yard.
Mistakes that throw off the order
- Skipping drainage. Water sitting under any surface softens the base and leads to ruts and potholes.
- Ordering exactly the math. Uneven ground and spillage nearly always need a little more than the flat calculation.
- Measuring only the main rectangle. Aprons, turnouts and curved edges add real square footage.
- Ignoring the base. A thin surface layer over soft soil fails early no matter how much material is on top.
Questions people ask
How many tons is 19 yards of gravel?
About 26.6 tons, with a typical range of 24.7 to 28.5.
How many pounds is 19 cubic yards of gravel?
About 53,200 pounds.
How much area does 19 yards of gravel cover at 4 inches?
About 1,539 square feet.
Why does gravel weight vary?
Stone size, the share of fines and moisture all change how much a yard weighs.
Is it better to buy by the ton or the yard?
Either works; just convert with the supplier’s own weight per yard so the two quotes compare fairly.
Related guides
- How Much Does a Ton of Gravel Cover? Depth Chart
- Tons to Cubic Yards for Gravel: Conversion Chart
- How Much Does a Yard of Crushed Stone Weigh?
- 17 Cubic Yards of Gravel in Tons
- 18 Cubic Yards of Gravel in Tons
As an Amazon Associate, AsphaltTons.com earns from qualifying purchases. Product links below are sponsored.