22A Gravel: Michigan Spec, Weight per Yard and Uses
Walk into almost any Michigan gravel yard and you'll see the pile labeled 22A. It's a road-commission staple: a dense-graded aggregate with a 1-inch top size and enough fines to pack hard. The name isn't a brand. It's a gradation class in the Michigan Department of Transportation (MDOT) Standard Specifications for Construction. Knowing what the spec actually requires helps you order the right pile, compare it with 21AA and 23A, and figure tons without guessing.
Run your gravel tons in the calculator →What 22A gravel is
MDOT's Section 902.05 lists five dense-graded aggregate classes for base course, surface course, shoulders, approaches and patching: 21AA, 21A, 22A, 23A and 23AA. "Dense-graded" means the stone is graded from coarse to fine so the small particles fill the gaps between the large ones. Rolled at the right moisture, it locks into a tight, load-carrying layer rather than a loose pile of marbles.
Under the spec, 22A can be made from natural gravel, crushed stone, iron blast-furnace slag, reverberatory furnace slag, or crushed concrete, blended with fine aggregate when needed. That's why one yard's 22A looks gray and angular while another's is tan, rounded pit gravel. Both can meet the same gradation. Ask your supplier what the source rock is if appearance or drainage matters to you.
The 22A gradation, side by side with its neighbors
MDOT Table 902-1 sets the percent of material, by dry weight, that must pass each sieve. The last column is "loss by washing" (LBW), MDOT's measure of the fine dust and clay that washes through a No. 200 sieve. Dashes mean no limit at that sieve.
| Class | 1½ in | 1 in | ¾ in | ½ in | ⅜ in | No. 8 | LBW |
|---|---|---|---|---|---|---|---|
| 21AA | 100 | 85–100 | — | 50–75 | — | 20–45 | 4–8 |
| 21A | 100 | 85–100 | — | 50–75 | — | 20–45 | 4–8 |
| 22A | — | 100 | 90–100 | — | 65–85 | 30–50 | 4–8 |
| 23A | — | 100 | — | — | 60–85 | 25–60 | 9–16 |
| 23AA | — | 100 | — | — | 60–85 | 25–60 | 9–16 |
Three things jump out of that table:
- 22A is smaller on top. Everything passes a 1-inch sieve, and at least 90% passes ¾ inch. The 21-series classes allow stone up to 1½ inches.
- 22A carries more sand-sized material. 30–50% must pass the No. 8 sieve, against 20–45% for 21AA. That gives a smoother, tighter finish and an easier surface to blade.
- 22A is not a "dirty" surface gravel. Its washing loss limit is 4–8%, the same as 21AA. The 23-series classes allow 9–16%, roughly double, because they're meant to stay as a bound driving surface. MDOT's footnotes let crushed-rock, slag or concrete dense-graded products go to 10% LBW for bases, surfaces, shoulders and approaches, and they put a separate cap on sources in Berrien County.
Crushed content and toughness
Table 902-2 adds two numbers people often get wrong. 22A needs a minimum of only 25% crushed material, the same as 21A and 23A. 21AA and 23AA need 95% crushed. That double-A is the crushed-content upgrade. All five dense-graded classes share a maximum Los Angeles abrasion loss of 50%. So a 22A made from rounded pit gravel can be fully in spec, and it won't interlock quite like an all-crushed 21AA.
Where MDOT uses 22A
The spec sections that call for each class tell you a lot about how 22A is meant to behave:
- Aggregate base (Section 302): 21AA, 21A or 22A, whichever series the plans show.
- Aggregate surface course (Section 306): 21A, 21AA or 22A when the gravel will later be paved; 23A or 23AA when it will stay gravel.
- Shoulders and approaches (Section 307): a Class I shoulder or approach gets 22A. If that Class I area will be paved, 21A, 21AA or 22A are all allowed. Class II uses 23A or 23AA.
MDOT's construction wiki puts it the same way: Class I approaches that won't be paved get 22A, period. MDOT's Road Design Manual explains why surface gravels like 23A carry more fines: soil binder (clay) makes the surface denser and less loose under traffic. That same binder is unwanted in a base because it slows drainage and invites frost heave. 22A sits between those jobs. It drains and supports like a base and finishes tighter than a coarse 21AA.
One rule worth knowing if your load is crushed concrete: MDOT bars crushed-concrete dense-graded aggregate within 100 feet of any stream, river, county drain or lake on its projects. It also limits recycled concrete 21AA, 21A or 22A where the layer drains into an underdrain, because of leachate. A private driveway isn't an MDOT project, but the reasoning carries over if your lane runs along a creek.
22A vs 21AA: which one for a driveway?
Both are allowed under pavement, so the choice usually comes down to how the driveway will be used.
- Choose 21AA when you want the strongest, most interlocking base under future asphalt or concrete. The 95% crushed requirement and the 1½-inch top size give it more bite. Our 21A gravel guide covers the 21-series in more detail.
- Choose 22A for a gravel driveway you'll drive on as-is, a road approach, or a top dressing over coarser base. The smaller stone and extra sand-sized fraction blade and roll to a smoother surface.
- Choose 23A only if you want a true surface gravel that binds with clay. MDOT specifies it for aggregate surfaces that will stay gravel. Its extra fines hold water, which is why MDOT keeps that kind of binder out of base layers.
If you're paving later, check your local road commission's approach permit first. The Lapeer County Road Commission's residential gravel approach sheet, for example, accepts 21AA, 22A or 23A at a minimum 8 inches deep. It bars any particle over 1½ inches and requires at least a 2% slope down and away from the road so water heads to the ditch, not the pavement.
How much does a yard of 22A weigh?
There isn't one exact number, because density depends on the rock, the moisture and how hard it's rolled. Two public figures bracket it well:
- MDOT's planning number: the Road Design Manual (6.02.04) says that for general purposes compacted aggregates are considered to weigh 4,000 lb per cubic yard, or 2.0 tons. It lists approximate unit weights of 148 lb/ft³ for natural aggregate, 144 for blast-furnace slag and 184 for steel-furnace slag, so a slag-based product will run heavier per yard.
- Measured values: a 2023 Wisconsin DOT research report (WHRP 0092-22-05) tested real stockpiles and compacted lifts. For ¾-inch dense graded base, the closest Wisconsin match to 22A's size, it measured 1.80–1.86 tons per compacted cubic yard. The same material expanded 36–47% going from compacted back to loose.
That second number matters if your supplier sells by the yard. A yard of loose material in a truck bed won't fill a yard of compacted driveway. If your yard sells by the ton, the scale ticket already accounts for it.
Quick table: tons of 22A per 100 square feet
| Compacted depth | Cubic yards | Tons at 1.83 t/yd³ (Wisconsin midpoint) | Tons at 2.0 t/yd³ (MDOT planning) |
|---|---|---|---|
| 4 in | 1.23 | 2.3 | 2.5 |
| 6 in | 1.85 | 3.4 | 3.7 |
| 8 in | 2.47 | 4.5 | 4.9 |
Worked example: a rural Michigan driveway
Say you're rebuilding a gravel drive 12 feet wide and 150 feet long with 6 inches of compacted 22A. The approach at the road needs the 8 inches our example county requires, over an area you measure at 20 by 24 feet. These dimensions are made up to show the method.
- Driveway volume: 12 × 150 × 0.5 ft = 900 ft³ ÷ 27 = 33.3 compacted yd³.
- Approach volume: 20 × 24 × 0.667 ft = 320 ft³ ÷ 27 = 11.9 yd³.
- Total: 45.2 compacted yd³.
- Tons: at the Wisconsin measured range of 1.80–1.86, about 81–84 tons. At MDOT's 2.0 planning figure, about 90 tons. Ordering near the middle and holding a few tons back for the last load is a sensible way to land between them.
- If sold by the loose yard: 45.2 × 1.36 to 1.47 = about 61–66 loose yd³.
That's several truckloads, so ask the yard what its trucks can legally carry, especially in spring. Our Michigan frost laws guide explains the seasonal axle limits that cut load sizes on many county roads. To measure a long, curving drive accurately, a rolling tape like the Zozen measuring wheel beats a 100-foot tape and a helper.
Placing and compacting 22A
MDOT's rules are written for highway crews, but they're a good checklist for a driveway too:
- Firm ground only. Sections 302 and 307 prohibit placing aggregate on frozen, soft, unstable or rutted subgrade. On soft clay, a woven separation fabric such as Super Geotextile woven driveway fabric (12.5 × 60 ft) under the stone helps keep it from sinking into the mud.
- Lift thickness. Section 302 compacts base in layers no less than 3 and no more than 8 inches. A thinner new layer gets blended with the layer below.
- Density and moisture. MDOT compacts Class I approaches and bases under asphalt to at least 98% of maximum unit weight, at a moisture content no wetter than optimum. In plain terms: damp, not soupy, and rolled until it stops moving.
- Grade for water. Shape a crown or cross slope and keep the finish within about ½ inch of grade, the tolerance MDOT uses. Then keep the ditch side open. Our gravel road maintenance guide covers crown and drainage in more depth.
For edges, culvert ends and spots a roller can't reach, a heavy hand tamper such as the Estwing 10 × 10 in steel tamper does the job in thin lifts. If the 22A is a base for asphalt, our asphalt base calculator figures the stone and the mix together.
22A gravel FAQ
What size is 22A gravel?
Under MDOT Table 902-1, all of it passes a 1 in sieve, 90 to 100% passes 3/4 in, 65 to 85% passes 3/8 in and 30 to 50% passes the No. 8 sieve, with 4 to 8% loss by washing.
What is the difference between 21AA and 22A?
21AA allows stone up to 1 1/2 in and must be at least 95% crushed. 22A tops out at 1 in, carries more sand-sized material and needs only 25% crushed material. Both have the same 4 to 8% washing-loss limit.
How much does a yard of 22A gravel weigh?
MDOT's Road Design Manual uses 4,000 lb (2.0 tons) per compacted cubic yard for aggregates. A Wisconsin DOT study measured 1.80 to 1.86 tons per compacted yard for a similar 3/4 in dense graded base.
Is 22A good for a gravel driveway?
Yes. MDOT specifies 22A for Class I approaches that will not be paved, and it is also allowed as base under pavement. Some county road commissions accept it for driveway approaches, such as Lapeer at 8 in minimum.
The bottom line
22A is MDOT's 1-inch-top dense-graded aggregate. 90–100% passes ¾ inch, 30–50% passes the No. 8 sieve, washing loss runs 4–8%, and it needs only 25% crushed material. MDOT uses it for bases, paved-later surfaces and Class I shoulders and approaches, so it suits gravel driveways and approaches. For tonnage, plan on about 1.8 to 2.0 tons per compacted cubic yard, and add 36–47% if you're buying loose yards.
Sources
- MDOT 2020 Standard Specifications for Construction, Section 902 Aggregates (902.05; Table 902-1 gradations and LBW footnotes; Table 902-2 crushed content and LA abrasion)
- MDOT Section 302, Aggregate Base Course (classes, 3–8 in layers, 98% density under HMA)
- MDOT Section 306, Aggregate Surface Course and Maintenance Gravel (paved-later vs gravel-surface classes)
- MDOT Section 307, Aggregate Shoulders and Approaches (Class I = 22A; density requirements)
- MDOT 2020 Standard Specifications for Construction with errata (full PDF)
- MDOT Construction Manual wiki: 307 Aggregate Shoulders and Approaches
- MDOT Road Design Manual, Chapter 6 (6.02.04 weight of aggregates; 6.02.08A slag weights; 6.02.09B base vs surface course)
- Wisconsin DOT / WHRP 0092-22-05 (2023): Weight-Volume Relationships and Conversion Factors for Soils and Aggregates of Wisconsin, Table E2
- Lapeer County Road Commission: Residential Driveway Approach, Gravel (Aggregate) Detail Sheet (2022)
As an Amazon Associate, AsphaltTons.com earns from qualifying purchases. Product links below are sponsored.
