AsphaltTons.com — asphalt tonnage calculator

2NS Sand: Michigan Spec, Weight per Yard and Uses

2NS sand is the Michigan Department of Transportation's name for natural concrete sand: clean sand graded from ⅜ inch down to fine grit, with very little silt or clay. MDOT puts it in concrete, prestressed beams, grout and mortar. Landscape yards across the state sell the same pile, often labeled sharp sand or construction sand, as paver bedding, a base under slabs, and a free-draining floor for horse stalls and runs. The name is a spec class, not a brand, so when a Michigan yard says "2NS," it is telling you which sieve limits the sand is supposed to meet.

Work out your 2NS yards and tons in the sand calculator →

What "2NS" means

The code comes from Section 902 of MDOT's 2020 Standard Specifications for Construction (the errata-incorporated edition, current as of April 30, 2025). Fine aggregates carry a "2" class number, and the letters tell you where the sand came from:

  • 2NS, natural sand. The spec defines it as fine, clean, hard, durable, uncoated sand particles free of clay lumps and soft or flaky material, formed by the natural breakdown of rock.
  • 2SS, stone sand. Sand manufactured by crushing stone. The parent rock has to meet the physical requirements for 6A coarse aggregate before it is crushed, and quarried limestone or dolomite 2SS cannot be used in any application exposed to vehicular traffic.
  • 2MS, mortar sand. A finer natural sand for mortar, with every grain passing the No. 4 sieve.

Section 902.08 also calls for the AASHTO T21 organic impurities test: the sand must not produce a color darker than Organic Plate No. 3. That screens out sand stained with topsoil or other organic matter, which can slow or weaken concrete.

The 2NS sieve limits

MDOT Table 902-4 sets the grading. Results are by dry weight using Michigan Test Method 109, with loss by washing (the dust and clay that rinse through the No. 200 sieve) measured by MTM 108.

Sieve2NS2SS2MS
⅜ in100100—
No. 495–10095–100100
No. 865–9565–9595–100
No. 1635–7535–75—
No. 3020–5520–55—
No. 5010–3010–3015–40
No. 1000–100–100–10
LBW (No. 200)0–3.00–4.00–3.0

Read that 2NS column top to bottom and you get a picture of the sand. Nothing is bigger than ⅜ inch, and no more than 5% is coarser than the No. 4 sieve (about 3/16 inch), so you will see a few small pebbles but no real stone. Between a fifth and two-thirds of it is coarse grit held between the No. 4 and No. 16 sieves. At the bottom end, no more than 10% passes the No. 100 sieve and no more than 3.0% washes out as dust. Low fines are the whole point: in concrete, extra fines raise the water demand, and under pavers they hold water and let the bedding shift.

Next to 2MS, you can see why mason sand makes smoother mortar. 2MS has to pass the No. 8 almost entirely (95–100%), while 2NS can keep up to 35% of its grains on that sieve. Our mason sand vs concrete sand guide covers that trade-off for the general, non-Michigan names.

Fineness modulus: the number on the producer's sheet

2NS, 2SS and 2MS also have to hold a steady fineness modulus (FM). The producer reports a base FM for each source at the start of each construction season, and it has to fall between 2.50 and 3.35. Any shipment that drifts more than 0.20 from that base is rejected (Table 902-4, footnotes c and d, testing by ASTM C136). FM is the sum of the cumulative percentages retained on the standard sieves divided by 100, so a higher number means coarser sand.

Here is an illustrative check using the midpoint of each 2NS band (not a real test result). Passing percentages of 100, 97.5, 80, 55, 37.5, 20 and 5 on the ⅜-inch through No. 100 sieves mean 0, 2.5, 20, 45, 62.5, 80 and 95 percent retained. Those add up to 305, so the FM is 3.05, inside MDOT's 2.50–3.35 window. The fineness modulus of sand post walks through the same math step by step.

Where MDOT uses 2NS

  • Concrete. Section 1004 lists fine aggregate 2NS or 2SS for portland cement concrete mixtures, but bars stone sand 2SS from concrete exposed to vehicular traffic. For pavement, curb and driveway concrete, natural 2NS is the default.
  • Prestressed concrete beams. Section 708 is stricter: provide 2NS fine aggregate, with no slag aggregate.
  • Grout and mortar. Section 1005 proportions R-1 bond grout at 1 part portland cement to 1 part 2NS by bulk volume, and R-3 mortar, used to set precast concrete barriers and fill between slope-protection blocks and riprap, at 1 part cement to 3½ parts 2NS.

Crushed concrete fines are not allowed in concrete mixtures at all under 902.08, and the Road Design Manual notes that crushed concrete sand has been prohibited in new concrete because of strength problems. If a pit offers recycled sand as "2NS," it is not 2NS by MDOT's definition.

2NS vs fill sand (Class II)

Ask for "fill sand" in Michigan and many yards will load MDOT Class II granular material, sometimes sold as "class 2 sand." It is a different product with a different job. Section 902.07 covers granular materials for fill and subbase, and Table 902-3 grades them much more loosely than 2NS:

MaterialTop sizeNo. 4No. 100LBW (No. 200)Typical MDOT use
2NS⅜ in95–1000–100–3.0Concrete, grout, mortar
Class II3 in (60–100 passing 1 in)50–1000–300–7Subbase, structure and trench backfill
Class IIIA⅜ in50–1000–300–15Storm sewer pipe bedding
Class III6 in (95–100 passing 3 in)50–100—0–15Embankment fill

Class II may contain stones up to 3 inches, can be half gravel by weight, and allows more than twice the wash-out fines of 2NS. That is fine for backfilling a trench or building up a subbase, where you want a compactable, free-draining granular layer. It is the wrong choice for screeding a 1-inch paver bed or batching concrete. Section 402 uses uncompacted Class IIIA as storm sewer bedding, and Section 902.07 lets a contractor substitute Class I, Class IIAA, or 21A, 21AA or 22A material for Class II.

The rule of thumb: buy 2NS when the sand goes in a mix or directly under a finished surface, and Class II when you are filling a hole or building grade under a base. Under a driveway or slab, Class II typically sits below a dense-graded base course such as 22A, not in place of it.

How much does a yard of 2NS weigh?

MDOT does not publish a weight for 2NS. Its Road Design Manual (section 6.02.04) uses 4,000 pounds per cubic yard as a general planning weight for compacted aggregates, but that number is for compacted base material on a road job, not a loose yard of sand dumped from a truck. For ordering sand, use the supplier's figure. Four Michigan yards posted these numbers on their 2NS product pages, checked November 20, 2026:

  • Greenfield Supplies (Detroit): 2,900 lb per yard, which they state as 1.45 tons.
  • Main's Landscape Supply (Southfield), "aka 2NS sand": 2,800 lb per yard.
  • Kalamazoo Landscape Supplies, Construction Sand (2NS): 2,800 lb per cubic yard.
  • Greenleaf Landscape Supply: approximately 2,700 lb per yard.

So plan on 1.35 to 1.45 tons per cubic yard, and about 1.4 tons if you have nothing better. Wet sand straight from a washing plant weighs more than sand that has drained in the pile, which is why the yards differ. Our yard of sand weight guide explains how moisture swings the number.

Prices on those same pages ran from $31.65 per yard (Kalamazoo) to $56.99 per yard (Southfield) before delivery, and one Brighton yard listed 2NS at $33 per ton. Delivery, minimums and seasonal pricing change the final bill, so call before you plan around a number.

Quick table: 2NS per 100 square feet

Loose cubic yards and tons at the low and high supplier weights above. These are estimates for ordering, not a pay quantity.

DepthCubic yardsTons at 2,700 lb/ydTons at 2,900 lb/yd
1 in0.310.420.45
2 in0.620.830.90
3 in0.931.251.34
4 in1.231.671.79
6 in1.852.502.69

Worked example: a 12-by-16 paver patio

Say you are laying a 12-by-16-foot paver patio in Michigan, with a compacted dense-graded base already in and a 1-inch bedding layer of 2NS on top. Check the patio dimensions and the run to the yard edge with a Zozen measuring wheel if the area is irregular, then do the math:

12 × 16 = 192 square feet. Times 1/12 foot of depth = 16 cubic feet. Divide by 27: 0.59 cubic yards. At 2,800 pounds per yard, that is about 1,660 pounds, or 0.83 tons. Most yards sell bulk sand by the yard, so a one-yard load covers it with some left to fill low spots.

Set two pipes or rails on the base, fill between them with damp 2NS, and pull a straight, rigid Bon 6-ft reinforced aluminum H screed across the rails to strike the bed flat. Do not walk on the screeded sand before the pavers go down. Bedding sand is not a substitute for base: if the gravel under it is thin or soft, the patio will settle no matter how good the sand is. How deep paver base should be covers that layer.

A bigger job, such as a 12-by-24-foot run-in stall floor 4 inches deep, works the same way: 288 square feet × 4/12 = 96 cubic feet, or 3.56 cubic yards. At 2,800 pounds per yard that is about 9,960 pounds, roughly 5 tons. Kalamazoo Landscape Supplies caps a single delivery at 12 yards, so a load of that size is one truck. Spread it in a couple of passes and firm it with a Estwing 10 × 10 in steel tamper around posts and gates, where a plate compactor will not reach.

Buying tips

  • Ask for the gradation. A yard selling 2NS for MDOT work will have a recent sieve report and a base fineness modulus for the source. A pile simply labeled "sharp sand" may or may not meet Table 902-4.
  • Don't swap in 2SS for anything that will be driven on. Limestone or dolomite stone sand is excluded from traffic-exposed applications, and MDOT keeps 2SS out of concrete exposed to vehicles.
  • Keep the pile clean. Store it on a tarp or a hard surface, away from topsoil. Organic contamination is exactly what the T21 test screens for.

2NS sand FAQ

What is 2NS sand?

2NS is MDOT's class for natural concrete sand. It must pass the 3/8-inch sieve completely, 95–100% must pass the No. 4, no more than 10% may pass the No. 100, and loss by washing is capped at 3.0%. It is used in concrete, grout and mortar, and yards sell it as paver bedding sand.

What is 2NS sand used for?

MDOT specifies it for portland cement concrete, prestressed beams, bond grout and mortar. Homeowners and landscapers use it as a 1-inch paver bedding layer, a clean sand under slabs, and a free-draining floor for horse stalls and runs.

What is the difference between 2NS sand and fill sand?

Fill sand in Michigan usually means MDOT Class II granular material. Class II can contain stones up to 3 inches, only 50–100% has to pass the No. 4 sieve, and it allows up to 7% wash-out fines, versus 3.0% for 2NS. Use Class II for backfill and subbase, and 2NS for mixes and bedding.

How much does a yard of 2NS sand weigh?

Michigan suppliers list 2,700 to 2,900 pounds per cubic yard, or about 1.35 to 1.45 tons. Use about 1.4 tons per yard for planning and ask your yard for its own figure, since wet sand weighs more.

Is 2NS the same as 2SS?

No. 2NS is natural sand; 2SS is stone sand made by crushing rock. The gradations are nearly the same, but 2SS allows 4.0% wash-out fines and MDOT keeps it out of concrete exposed to vehicular traffic.

The bottom line

2NS is MDOT's natural concrete sand: 100% passing ⅜ inch, 95–100% passing the No. 4, no more than 10% passing the No. 100, at most 3.0% wash-out fines, and a fineness modulus held within 0.20 of a base value between 2.50 and 3.35. It belongs in concrete, grout and mortar and makes a good paver bed. It is not the same as Class II fill sand, which is coarser, dirtier and meant for backfill and subbase. Plan on about 1.4 tons per loose cubic yard, which means about 0.83 tons for a 1-inch bed under a 12-by-16 patio. Check the weight and price with your yard before you order.

Sources

As an Amazon Associate, AsphaltTons.com earns from qualifying purchases. Product links below are sponsored.