6 Cubic Yards of #57 Stone in Tons
6 cubic yards of #57 stone in tons works out to about 8.1 tons using a planning weight of 1.35 tons per yard. Real loads land between roughly 7.8 and 8.7 tons depending on stone size, fines and moisture. That is about 16,200 pounds.
Volume and tonnage calculator →The conversion
- Yards × tons per yard: 6 × 1.35 = 8.1 tons.
- Low end: 6 × 1.3 = 7.8 tons.
- High end: 6 × 1.45 = 8.7 tons.
If your supplier quotes a different weight per yard, multiply by theirs.
What 6 yards covers
| Depth | Square feet |
|---|---|
| 2 in | 972 |
| 3 in | 648 |
| 4 in | 486 |
| 6 in | 324 |
About #57 stone
#57 stone is a clean crushed stone in roughly the 1/2 to 1 inch range with very few fines. It drains fast, which suits drainage layers and the top of a gravel drive, but it does not pack into a hard crust by itself.
Hauling 6 yards
Plan the delivery around 8.1 tons: one small truck in most areas. A pickup is a poor fit for anything past a fraction of a yard; see how much gravel a half-ton pickup can carry.
Before you order
- Confirm whether the yard prices #57 stone by the ton or by the yard.
- Add about 10 percent for compaction and uneven ground.
- Clear a firm spot for the truck to dump.
The volume and tonnage calculator converts any area and depth into yards and tons.
Good and poor uses for #57 stone
Good uses:
- French drains and drainage layers
- The top course of a gravel driveway
- Under sheds where water needs to drain away
Think twice for:
- A standalone base, since it does not pack hard without fines
- Paver setting beds
- Walk paths meant for strollers or wheelchairs
Quick reference numbers
- Per inch over 100 sq ft: about 0.42 tons of #57 stone (0.31 cubic yards).
- Per inch over 1,000 sq ft: about 4.2 tons.
- Another size for comparison: a 8x16 area at 4 inches takes about 2.1 tons.
- Weight used here: about 1.35 tons per cubic yard.
Where estimates go wrong
- Measuring only the main rectangle. Aprons, turnouts and curved edges add real square footage.
- Forgetting that compaction shrinks loose material. A loose 4-inch spread of a dense-graded stone may finish closer to 3 inches after rolling.
- Assuming every supplier uses the same weight. Two yards selling the same product name can quote different tons per yard.
- Ordering exactly the math. Uneven ground and spillage nearly always need a little more than the flat calculation.
Questions people ask
How many tons is 6 yards of #57 stone?
About 8.1 tons, with a typical range of 7.8 to 8.7.
How many pounds is 6 cubic yards of #57 stone?
About 16,200 pounds.
How much area does 6 yards of #57 stone cover at 4 inches?
About 486 square feet.
Why does #57 stone weight vary?
Stone size, the share of fines and moisture all change how much a yard weighs.
Is it better to buy by the ton or the yard?
Either works; just convert with the supplier’s own weight per yard so the two quotes compare fairly.
Related guides
- Number 57 Stone: Size, Weight, Uses, and Coverage
- Tons to Cubic Yards for Gravel: Conversion Chart
- How Much Does a Yard of Crushed Stone Weigh?
- 4 Cubic Yards of #57 Stone in Tons
- 5 Cubic Yards of #57 Stone in Tons
As an Amazon Associate, AsphaltTons.com earns from qualifying purchases. Product links below are sponsored.