Asphalt Milling Teeth: Wear Stages, Changes and Drum Math
Milling teeth are the small carbide-tipped picks that do the actual cutting on a cold planer. A full-size highway machine carries hundreds of them, and a skid steer planer carries a few dozen, but the story is the same on both: when the teeth are sharp and turning freely, the drum cuts fast and leaves an even texture. When they're blunt, broken or seized, the machine slows down, works harder, chews up its own holders and leaves streaks that an inspector can see from the truck.
Below: how a tooth is built, how makers match teeth to the job, how to read wear, what DOT specs require, safe changing, and a worked cost example for a skid steer planer.
Figure the tons of millings a cut will make →What a milling tooth actually is
Crews call them teeth, bits, picks or cutters. Manufacturers usually call them round-shank picks or rotating picks. Whatever the name, a typical tooth for a road milling drum has four parts:
- Carbide tip. A tungsten carbide point brazed into the top of the tooth. Wirtgen's pick catalog lists carbide weights from about 20 g to 48 g per pick depending on the model, and it separates cap-shaped tips (asphalt, from soft to hard) from cylindrical tips (hard materials such as concrete).
- Steel body. The head that holds the carbide and takes the abrasion around it. Kennametal's Road King catalog describes a body "rib zone" that adds clearance as the pick wears, reducing drag on the drum.
- Shank and retainer. A round shank that slides into the holder and is held by a clamping sleeve or retainer. Both Wirtgen's GENERATION X² picks and Kennametal's Road King picks listed here use a 20 mm shank (Kennametal lists it as 0.76 in).
- Washer or wear plate. A hardened disc at the base of the head that protects the holder from the abrasive millings flowing past it.
The tooth sits in a holder (sometimes called a sleeve or upper part), and the holder sits in a block or base welded to the drum. Teeth are consumables you change by the box. Holders last longer, and blocks are the most permanent piece. The road milling machine guide covers how the drum, conveyor and grade controls fit around all this.
Why the teeth have to rotate
A round-shank pick is meant to spin slowly in its holder as it cuts, so the carbide wears evenly all the way around, like a pencil turning in a sharpener. A U.S. patent application on predicting milling tool wear (US 2020/0064242) explains what happens when that fails. It sorts drum wear into a few cases: normal, rotationally symmetrical wear, where the carbide is simply used up; holder wear at the contact face; and lopsided wear on the tip or head because the pick did not turn enough. The lopsided case is the bad one. The patent says it causes a poor milling pattern and raises the risk of tool breakage. It also notes that worn or broken bits can damage the holders, and worn holders can in turn damage the drum.
Kennametal's maintenance tips for Road King picks (published through dealer Texas Contractors Equipment) make the same point from the holder side: a rotating pick works best with support and freedom to turn, and loose or worn sleeves or material packed around the tool can lead to flat spots on the carbide or fractures. A tooth with a flat face on one side is telling you something is stopping it from turning.
Choosing teeth for the job
There's no single best tooth. The makers match the tooth to the machine size and how hard the pavement is. Here is what two of them publish:
| Tooth | Maker's stated use | Notes from the maker |
|---|---|---|
| Kennametal RK31 | Softer asphalt, smaller machines (lower power per pick) | Complete maintenance cycle (change the whole drum) |
| Kennametal RK32 | Hard asphalt, most machines | Selective maintenance cycle (change teeth as needed) |
| Kennametal RK54 | Very hard asphalt, larger machines | Selective maintenance cycle |
| Wirtgen GENERATION X² (carbide) | Universal: soft asphalt, hard asphalt or concrete | Carbide recommended where sudden impact loads are expected in mixed material |
| Wirtgen PCD milling tools | Uniform asphalt layers with no sudden impact loads; surface course rehab up to 8 cm deep; fine and micro milling | Polycrystalline diamond tip with very little lengthwise wear |
| Wirtgen GENERATION C² | Concrete and asphalt with ECO Cutter drums | Shorter clamping sleeve and revised shank for higher fracture resistance |
Pavements differ a lot in how hard and abrasive they are to cut, which is why both makers sell several grades and leave it to the crew to match the tooth to the road.
Carbide or diamond? Wirtgen pitches its PCD (diamond-tipped) tools for shallow, even asphalt work. Its brochure charts possible tool-cost savings of around 60% per ton milled under the right conditions, counting only tool and maintenance costs. The trade-off is that diamond tips are made for uniform asphalt layers, while carbide is still Wirtgen's recommendation where the cut may hit sudden impact loads, such as patched, mixed or concrete-bearing pavement.
Reading tooth wear
Kennametal's Road King flyer splits a tooth's life into four stages. They make a handy shared vocabulary for a crew walking the drum:
- Stage 1: new tooth with sharp edges, rib features and full gauge length.
- Stage 2: some wear but still cutting well, with nearly full gauge length.
- Stage 3: the carbide is blunt, the gauge is shorter and cutting is falling off. Kennametal says these teeth can be changed or run longer, depending on how fussy the job is about surface quality.
- Stage 4: the carbide still shields the block but no longer cuts. Change it.
Kennametal adds that a rotating pick gives the best value when the steel body and the carbide wear out at about the same time. A tooth that is dull, bent, cracked, burred or showing excessive steel wear should not go back into the cut. While you're down there, look past the teeth: replace loose or worn holders and sleeves, and check blocks for unusual wear on their sides and in the bore.
Wirtgen's newer picks and holders show how much the holder matters. The company says the grooved wear plate on its GENERATION X² picks wears a centering profile into the holder's contact face within 50 operating hours, which improves rotation. It also says this extends the holder's service life by more than 25%. On its HT22 PLUS holders, Wirtgen lists a torque check interval of every 500 hours for the holder bolts.
What DOT specs say about worn teeth
On public work, the condition of the teeth isn't just a cost question. Several state specifications call it out directly:
- Nebraska (Section 510, Cold Milling): broken, missing or worn teeth must be replaced. If the milled surface will carry traffic for more than 30 days, the texture must be uniform, with satisfactory ride and skid resistance, and continuous longitudinal striations are not allowed.
- Tennessee (TDOT milling best practices): lists the condition of the cutting teeth as one of the factors in milled-surface quality and says teeth should be inspected routinely for damage or uneven wear. Lines or streaks in the milled surface are the warning sign. TDOT's spec 415.03 bars scabbing, scallops, gouges, ridges or other flaws from worn cutter teeth on Interstates and controlled-access freeways.
- Iowa (Section 2531, Pavement Surface Repair by Milling): this is a surface-repair spec, not ordinary removal milling, and it sets a tighter drum: at least 60 cutting teeth per foot of width at about 1/4 in transverse spacing, with tooth faces pointed to no more than 75 degrees. Broken teeth must be replaced immediately.
Spacing matters as much as condition. TDOT notes that drums typically come with teeth spaced 5/8 in (standard) or 5/16 in (fine), and that more teeth generally means a smoother texture. Its spec caps forward speed for milling before hot mix overlays at 60 ft/min with 1/2 to 5/8 in spacing and 80 ft/min with spacing under 1/2 in. If you need a finer finish for a thin overlay, see our guide to micro milling asphalt.
Changing teeth safely
Follow your machine's manual for shutting down and securing the drum before anyone reaches into the housing. For the teeth themselves, Kennametal's tips are clear:
- Wear eye protection. Kennametal calls for safety goggles or a face shield. A wraparound anti-fog face shield worn over safety glasses covers both.
- Install with a soft blow. To avoid chipping the carbide, Kennametal says to seat teeth with a soft (copper) hammer, a rubber mallet or an air hammer tool. Brass and copper non-marring hammers are the usual shop choice.
- Seat it once. Make sure the tooth is fully seated and retained before it goes back into the cut, and don't keep striking a seated tooth. That can crack the tip or damage the retainer.
- Expect heat. Teeth can be hot right after milling.
- Pull with the right tool. Remove teeth with a bit puller, hand punch, air hammer punch or air hammer chisel. Both Wirtgen and Kennametal sell picks with an extractor (puller) groove for this. Cat says the tools needed to change bits come with its skid steer cold planers.
Teeth also wear faster when they run dry and dusty. Cutting asphalt with a drum creates dust, and OSHA's construction silica standard (29 CFR 1926.1153, Table 1) sets out the controls. Small drivable milling machines (less than half-lane) need supplemental water sprays with a surfactant. Large machines (half-lane and up) milling asphalt need exhaust ventilation on the drum enclosure plus water sprays. Keeping the water system working is part of keeping the teeth alive.
Worked example: a full tooth change on a skid steer planer
The figures below come from the cited spec pages and a listing checked on November 11, 2026. Prices change, and the tonnage uses a labeled planning density. Use it as a method, not a quote.
- Count the teeth. Cat lists 54 conical bits on its PC306 cold planer, which has a 23.6 in working width and 6.7 in maximum depth. (The newer PC306B lists 60.) Our skid steer planer guide compares the other heads.
- Price the box. An aftermarket box of 50 milling/zipper teeth (RK3-02P style, large carbide tip with washer) was listed at $1,186.50 when checked, or about $23.73 per tooth.
- Cost a full change. 54 × $23.73 ≈ $1,281 in teeth. You'd need two boxes and would have 46 spares. A selective change of, say, the 10 worst teeth is about $237. This is why makers like Kennametal separate "complete" and "selective" maintenance.
- Relate it to the work. Say the planer takes 2 in off a 500 ft run at roughly its 2 ft width: 2 × 500 × (2 ÷ 12) ≈ 167 ft³ in place. At a planning density of 145 lb/ft³ for in-place asphalt, that's about 24,200 lb, or 12.1 tons of millings to haul. Our asphalt millings calculator does this math for other sizes, and asphalt milling cost shows how contractors bid it.
- Scale up. A drum built to Iowa's 2531 surface-repair minimum of 60 teeth per foot would carry at least 360 teeth on a 6 ft width before spares. That's the same arithmetic at highway scale.
Asphalt milling teeth FAQ
How often should milling teeth be changed?
There is no fixed hour count; it depends on the pavement and the tooth. Kennametal describes four wear stages and says Stage 4 teeth, where the carbide no longer cuts, must be changed, while Stage 3 teeth can be changed or run longer depending on how smooth the surface has to be.
Why are my milling teeth wearing on one side?
Round-shank picks are designed to rotate in their holders. One-sided wear usually means a tooth is not turning, often because of a worn or loose holder or packed material. Lopsided wear leads to a poor milling pattern and a higher risk of breakage, so check the holder as well as the tooth.
What is the spacing of teeth on a milling drum?
Tennessee DOT notes that drums typically come with teeth spaced 5/8 in (standard) or 5/16 in (fine). Iowa's surface-repair milling spec asks for at least 60 teeth per foot of width at about 1/4 in spacing. Closer spacing leaves a smoother texture.
How do you remove milling teeth?
Use a bit puller, hand punch, air hammer punch or air hammer chisel, per Kennametal's guidance, and wear goggles or a face shield. Install new teeth with a soft copper hammer, rubber mallet or air hammer tool, and don't keep striking a tooth once it is seated.
The bottom line
Milling teeth are carbide-tipped, round-shank picks that are supposed to rotate in their holders and wear evenly. Pick the grade for the pavement and machine, walk the drum often, and change Stage 3 and 4 teeth before they cost you holders or a failed texture. Several DOT specs require broken or worn teeth to be replaced. Seat new teeth with a soft blow, pull them with a proper bit puller, and keep the water system running.
Sources
- Wirtgen: Cutting Tools for Cold Milling Machines brochure (GENERATION X², PCD up to 8 cm, ~60% tool-cost savings chart, C², HT22 PLUS 500 h bolt torque checks)
- Wirtgen: Picks GENERATION X² catalog (20 mm shank, carbide weight per pick, centering profile in under 50 h, 25%+ holder life)
- US Patent Application 2020/0064242, Wear prognosis method and maintenance method (bit and holder wear states)
- Kennametal: Maximize Your Tool Life with the Next Generation of Road King (RK31/RK32/RK54, wear stages 1–4)
- Kennametal Road King catalog via Texas Contractors Equipment (20 mm / 0.76 in shank, body rib zone, box quantities)
- Texas Contractors Equipment: Kennametal Road King productivity tips (install, remove, tool/holder/block inspection)
- Nebraska DOT Standard Specifications Section 510, Cold Milling (510.03 and 510.04)
- Tennessee DOT: Milling Best Practices (tooth spacing, tooth condition, spec 415.03 speeds and surface rules)
- Iowa DOT Section 2531, Pavement Surface Repair (Milling) (60 teeth per foot, 1/4 in spacing, 75 degree point)
- Caterpillar: PC306 cold planer specifications (54 conical bits, bit options, bit-changing tools included)
- OSHA 29 CFR 1926.1153, Respirable crystalline silica in construction, Table 1 (xiv) and (xv) milling machines
As an Amazon Associate, AsphaltTons.com earns from qualifying purchases. Product links below are sponsored.
