Crack Router: Machine Types, Specs and Reservoir Sizes
A crack router is a walk-behind machine that grinds a clean, square-sided slot along an asphalt crack so hot-poured sealant has a proper pocket to sit in. If you are pricing one to buy, renting one for a parking lot, or trying to figure out how many hours and how many boxes of sealant a routing job will take, this guide goes through the machine itself: the types, the specs that matter, the reservoir sizes state DOTs ask for, and the production math.
Estimating a sealing job? Open the driveway sealer calculator →What a crack router actually does
Most pavement cracks are ragged, narrow and full of dirt. Pour sealant on top and it mostly bridges the gap, bonding to a thin strip of dusty edge. A router widens the top of the crack into a uniform channel the FHWA crack-treatment manual calls a reservoir. The sealant then bonds to two fresh, rough sidewalls and has enough thickness to stretch when the crack opens in cold weather.
The FHWA Manual of Practice (FHWA-RD-99-147) states the goal of crack cutting plainly: a uniform, rectangular reservoir, centered over the crack, cut with as little damage to the surrounding pavement as possible. Every buying and operating decision below comes back to that one sentence. If you want the bigger picture of when a crack should be routed at all, our guide to routing cracks before sealing them covers that judgment call.
Three kinds of crack-cutting machines
"Crack router" usually means the rotary-impact type, but the FHWA manual groups three machines under crack cutting. Its Table 8 gives a production range for each, which I've converted from meters per minute to feet per hour:
| Machine | How it cuts | FHWA production | Trade-off |
|---|---|---|---|
| Rotary-impact router | Carbide-tipped cutters on pins swing out from a spinning head and chip the slot | 3.5–4.5 m/min (about 690–890 ft/hr) | Fastest; can spall edges, especially with the wrong bits |
| Vertical-spindle router | A bit spins on an upright shaft, like a big wood router | 0.5–1.0 m/min (about 100–200 ft/hr) | Least damaging, most maneuverable, but slow |
| Random crack saw | A 150–200 mm (6–8 in) diamond blade follows the crack | 1.0–2.5 m/min (about 200–490 ft/hr) | More rectangular slot with smoother walls; best on fairly straight cracks |
The manual's equipment table recommends using routers only with sharp carbide-tipped bits (or diamond for the spindle type) and says carbide router bits are "highly recommended" over steel ones. It also points out that crack cutting is often the slowest step in a sealing crew's day, which is why most contractors and agencies end up running rotary-impact machines.
Manufacturer numbers run higher than the FHWA range. Crafco rates its Model 30 router at a typical 1,000–2,000 linear feet per hour in asphalt, depending on the aggregate. Treat the FHWA range as a conservative planning figure and the brochure figure as what a practiced operator gets on cooperative pavement.
Specs on two common rotary-impact routers
Two names come up again and again when people search for a crack router for sale or rent: Crafco and Marathon. Here's what each manufacturer publishes today (checked November 2026):
| Spec | Crafco Model 30 Router | Marathon CR300K |
|---|---|---|
| Engine | Gas V-twin, 25 hp class (24.9 hp Honda EFI in the brochure; 27 hp Kohler listed in the current manual) | 27 hp Rehlko diesel V-twin |
| Cutter head | Six sprocket-shaped, carbide-tipped cutters on an 11¾ in head | Six carbide-tipped blades on a 12 in head of 1 in steel plate |
| Cut width | 3/8 in to 2 in (set with spacers) | Up to 2 in (dealer listing) |
| Max depth | 1⅜ in | 1½ in (dealer listing) |
| Weight | About 550 lb shipping (650 lb with dust control) | About 522 lb (586 lb with dust collection) |
| Depth control | Electric actuator on the handle plus a depth indicator | Fingertip linear actuator plus an indicator plate |
Both makers offer a dust-control version that vacuums the cuttings into a collector. Crafco's selection chart pitches it for cleaner working conditions, longer engine and air-filter life, and areas with visible-emission dust rules. Crafco also sells a self-propelled version, and its chart suggests self-propelled when the roads have grades, when the machine gets pushed on and off a trailer, or when someone will be routing for an hour or two a day.
At 500-plus pounds, neither machine goes in a pickup bed without a ramp and a plan. Most crews tow them on a small trailer or carry them on the melter trailer.
How wide and deep to rout
The width and depth you set is the single biggest choice on the job, because it sets the sealant's shape factor, its width divided by its depth. The FHWA manual recommends a shape factor of 1 for rubber-modified asphalt sealants (as wide as it is deep) and 2 for silicone. Here is what a few published sources call for:
| Source | Routed reservoir | Notes |
|---|---|---|
| FHWA-RD-99-147 figure 6 | 12–19 mm (about ½–¾ in) wide and deep for the standard reservoir; a deep-reservoir option is drawn at 25 mm (1 in) deep | Shape factor 1 for rubberized asphalt |
| Minnesota field handbook (MnDOT / LRRB) | ¾ in × ¾ in | Total band about 2½ in: the ¾ in rout plus a ¾ in overband on each side, kept as thin as possible |
| Ohio DOT Item 423 (2005 CMS) | ¾ in wide × 1 in deep when routing is specified | Applies to cracks narrower than ¾ in; sawed cracks ¾–⅞ in wide, ⅞–1 in deep |
On the Crafco machine you set width by rearranging spacers between the cutters on their pins, and depth with the actuator. The Model 30 manual says each shaded band on the depth indicator is roughly ¼ in, and it recommends two passes for anything deeper than ¾ in. It also warns that cutters wear, so the depth drifts and needs resetting through the day.
Which cracks are worth routing
Routing is the prep step for crack sealing, not crack filling. FHWA's selection table puts sealing candidates at roughly 5–19 mm wide (about ¼ to ¾ in), with more than 3 mm of horizontal movement a year and edge deterioration under 25% of the crack length. Those are typically transverse thermal and reflective cracks. Non-working cracks with little movement usually get filled without cutting. If you're still deciding which treatment a crack needs, see crack seal versus crack fill.
The payoff is real. FHWA reports SHRP H-106 results showing rubberized sealants placed in routed working cracks lasting 5–9 years, against 2.5–5 years for the same material overbanded on unrouted working cracks.
A few FHWA field rules worth taping inside the truck:
- Secondary cracks: only cut a secondary crack if it's more than 300 mm (about 12 in) from the primary. Closer than that, two slots weaken the asphalt between them, so just clean and seal it.
- Missed segments: the inspection checklist calls for fewer than 5% missed crack length. Centering the cutter on the crack gives you room to wobble.
- Cold or coarse pavement: very cold surfaces, coarse mixes and dull cutters all cause spalled edges and misshapen channels. Check the slot shape as you go.
- Season: FHWA suggests sealing in moderately cool weather, about 7–18 °C (45–64 °F), in spring or fall, when cracks sit near the middle of their working range.
Running a router without hurting yourself or the pavement
On the Crafco Model 30, the operator walks backward, guiding the machine with both hands. The manual has a pointed kickback warning: the router pulls toward the operator, and tightly compacted surfaces, deep or wide cuts, or hard aggregate can jerk it suddenly. Keep the skid plate in contact with the pavement, and know your stop: push down hard on the handle or let go of the clutch handle. Engage the clutch before lowering the head into the crack. A bouncing or hammering feel usually means you're going too fast or the cutters are worn out of round.
Routing throws chips and dust, and the engine and head are loud. The FHWA safety list for routers and saws includes eye and hearing protection. Wraparound glasses such as these NoCry ANSI Z87 anti-fog safety glasses and a pair of Pro For Sho 34 dB NRR earmuffs are a cheap baseline for the operator and whoever runs the air lance behind them.
After cutting, the slot has to be blown clean and dry. Leftover fines act as a bond breaker. Then comes the melter. Our crack sealing machine guide covers melters and pour pots, and the tar kettle guide explains the older direct-fire kettles you'll still see on used-equipment lots.
Worked example: a 1,200-foot parking lot job
This example is illustrative. Say you've walked a lot with a measuring wheel and counted 1,200 linear feet of working cracks worth sealing. You'll cut a ¾ × ¾ in reservoir and use a rubberized sealant that weighs 10.5 lb per gallon (Crafco's published unit weight for RoadSaver 221, sold in 30 lb boxes).
| Step | Math | Result |
|---|---|---|
| Routing time, FHWA rotary-impact range | 1,200 ft ÷ 690–890 ft/hr | about 1.3–1.7 hours of cutting |
| Routing time, Crafco brochure range | 1,200 ft ÷ 1,000–2,000 ft/hr | about 0.6–1.2 hours |
| Reservoir volume per foot | 0.75 in × 0.75 in × 12 in | 6.75 in³ per ft |
| Reservoir volume, whole job | 6.75 × 1,200 = 8,100 in³ ÷ 231 in³/gal | about 35.1 gal |
| Thin overband (1¾ in extra width × ⅛ in thick) | 0.219 in² × 12 × 1,200 = 3,150 in³ ÷ 231 | about 13.6 gal |
| Total sealant | 48.7 gal × 10.5 lb/gal | about 511 lb |
| Boxes to order | 511 ÷ 30 lb | 17.0, so 18 boxes before waste |
The 1¾ in extra width matches the MnDOT handbook's 2½ in total band, and ⅛ in is about the 3 mm band thickness shown in the FHWA figures. Two things push real usage up: cracks that open wider below the slot swallow extra material, and every melter has some left in the tank at the end of the day. Many crews add a box or two of margin. If you switch to Ohio's ¾ × 1 in slot, the reservoir alone climbs to about 46.8 gallons, roughly 490 lb, before any overband. For the coverage math on bagged and jug fillers used on smaller jobs, see crack filler coverage per gallon.
Notice what the numbers say about the schedule. Even at the slow end, the router is not the bottleneck for one lot. The bottleneck is cleaning and pouring. FHWA's Table 8 puts compressed-air cleaning at 3.0–4.5 m/min and a melter-applicator at 4.5–8.0 m/min with a two-person crew plus a driver, so cutting and cleaning set the pace.
Buy, rent, or hire it out
- Hire it out if you have one driveway or a small lot. A router, compressor or hot-air lance, and melter is a big equipment spread for a few hundred feet of cracks.
- Rent when you have a single larger job. Ask the rental yard what cutters are on the head and how worn they are. Dull cutters mean spalls and a slow, hammering cut.
- Buy when sealing is a regular line item. Price in spare cutter sets, a trailer, and whether you need the dust-control or self-propelled version. A used machine with a worn head and shaft can cost more in parts than it saved.
For finishing the band after the pour, a V-shaped crack squeegee like the Kraft Tool GG816 push-style crack squeegee is the hand tool the FHWA manual describes: a heavy-duty U- or V-shaped squeegee. If the cracks turn out to be too far gone for sealing and the area needs a patch instead, the asphalt tonnage calculator will size the hot mix.
Crack router FAQ
What does a crack router do?
It cuts a uniform, rectangular reservoir centered over an asphalt crack so hot-poured sealant can bond to clean sidewalls and stretch as the crack opens and closes.
How wide and deep should cracks be routed?
A 3/4 by 3/4 in reservoir is common for rubberized sealant; MnDOT's field handbook uses that size. Ohio DOT Item 423 calls for 3/4 in wide by 1 in deep. FHWA recommends a width-to-depth ratio of 1 for rubberized asphalt sealants.
How fast is a crack router?
FHWA lists rotary-impact routers at 3.5 to 4.5 m/min, about 690 to 890 ft per hour. Crafco rates its Model 30 at a typical 1,000 to 2,000 ft per hour in asphalt.
How much does a crack router weigh?
Published figures run about 522 lb for a Marathon CR300K and about 550 lb shipping weight for a Crafco Model 30, with dust-control versions near 586 to 650 lb.
Do all cracks need routing?
No. Routing is prep for sealing working cracks, roughly 1/4 to 3/4 in wide with more than 3 mm of yearly movement. Non-working cracks are usually filled without cutting.
The bottom line
A crack router cuts a clean reservoir so sealant bonds to fresh sidewalls and can stretch with a working crack. Rotary-impact routers are the production choice at roughly 690–2,000 ft per hour depending on whose number you use. Typical machines run a 25–27 hp engine, cut up to 2 in wide and about 1⅜–1½ in deep, and weigh 520–650 lb. A ¾ × ¾ in slot is the common target for rubberized sealant. That works out to about 6.75 in³ of sealant per foot before overband, or roughly 35 gallons per 1,200 feet.
Sources
- FHWA-RD-99-147, Materials and Procedures for Sealing and Filling Cracks in Asphalt-Surfaced Pavements: Manual of Practice, Part A (Tables 3, 6, 7; figure 6; shape factor; SHRP H-106 service lives)
- FHWA-RD-99-147, Part B (Table 8 production rates; crack saw; 4.3 crack cutting; inspection checklist D.1)
- Crafco Pavement Routers brochure (cut width, production rate, selection chart)
- Crafco Model 30 Pavement Router manual, Rev R (specifications table, operating instructions)
- Marathon Equipment CR300K brochure and J.D. Honigberg Marathon router listing (width and depth)
- Minnesota LRRB / Mn/DOT Asphalt Pavement Maintenance Field Handbook (rout and seal)
- Ohio DOT Item 423, Crack Sealing, Hot Applied (2005 CMS)
- Crafco RoadSaver 221 product data sheet (10.5 lb/gal, 30 lb boxes)
As an Amazon Associate, AsphaltTons.com earns from qualifying purchases. Product links below are sponsored.
