How Many Tons of Asphalt for a 30x100 Parking Area?

How many tons of asphalt for a 30x100 parking area comes down to thickness. The area is 30 × 100 = 3,000 square feet. Using a common planning density of about 145 pounds per cubic foot for compacted hot mix, a 2-inch mat needs roughly 36.2 tons and a 3-inch mat roughly 54.4 tons, before any allowance for waste or uneven base.

Asphalt tonnage calculator →

Step-by-step math for 30x100

Area: 30 ft × 100 ft = 3,000 sq ft.
Thickness in feet: 3 inches ÷ 12 = 0.25 ft.
Volume: 3,000 × 0.25 = 750 cubic feet.
Weight: 750 × 145 lb = 108,750 lb.
Tons: divide by 2,000 = 54.4 tons.

Swap in your own thickness and the plant’s stated density if you have it. The asphalt tonnage calculator runs the same steps.

Tons at common thicknesses

Compacted thickness	Cubic feet	Tons (145 lb/ft³)	Tons +5%
2 in	500	36.2	38.1
2.5 in	625	45.3	47.6
3 in	750	54.4	57.1
4 in	1,000	72.5	76.1

Choosing a thickness

An overlay on pavement that is cracked but structurally sound is usually 1.5 to 2 inches. A new parking area on fresh base is more often 2.5 to 3 inches compacted. Where garbage trucks, campers or a loaded pickup will turn, plan on the heavier end and a thicker stone base below.

Ordering and trucks

At 3 inches, 54.4 tons is about 5 tandem-axle loads if a truck carries around 14 tons, though legal loads vary by state and truck. Plants often have minimum orders, and small jobs may carry a short-load charge. See how many tons in a truckload of asphalt for more on load sizes.

Things that change the tonnage

Uneven base. Low spots fill with extra mix. A base that is graded and compacted flat keeps the tonnage close to the math.
Edges and flares. Curved edges, a wider apron at the street or a turnaround add square footage. Measure those separately and add them in.
Density. Mixes typically range from about 140 to 150 lb per compacted cubic foot. Ask your plant for its number if you need tight figures.
Waste. Many estimators add 5 to 10 percent for handling, raking and thickness variation.

Pricing it out

Multiply your tonnage by the per-ton price your local plant or contractor quotes. Installed prices also cover base work, equipment and labor, so material tons are only part of the bid. See asphalt cost per ton for what goes into a quote.

Where asphalt fits

Good uses:

Driveways, parking pads and private lanes that need a smooth, sealed surface
Overlays on old pavement that is cracked but still structurally sound
Areas where snow will be plowed, since a paved surface does not throw stone

Think twice for:

Ground that stays soft or wet, unless the base and drainage are fixed first
Very small patches, where bagged cold patch is often simpler
Jobs in cold weather, since hot mix needs warm temperatures to compact properly

Quick reference numbers

Per inch over 100 sq ft: about 0.62 tons of asphalt (0.31 cubic yards).
Per inch over 1,000 sq ft: about 6.2 tons.
Another size for comparison: a 20x25 area at 3 inches takes about 9.3 tons.
Weight used here: about 2.0 tons per cubic yard (roughly 145 lb per compacted cubic foot).

Where estimates go wrong

Assuming every supplier uses the same weight. Two yards selling the same product name can quote different tons per yard.
Measuring only the main rectangle. Aprons, turnouts and curved edges add real square footage.
Ordering exactly the math. Uneven ground and spillage nearly always need a little more than the flat calculation.
Skipping drainage. Water sitting under any surface softens the base and leads to ruts and potholes.

Questions people ask

How many tons of asphalt for a 30x100 parking area at 2 inches?

About 36.2 tons of compacted asphalt, or around 38.1 tons with a 5 percent allowance.

How many tons for a 30x100 parking area at 3 inches?

About 54.4 tons at 145 lb per cubic foot.

How many square feet is a 30x100 parking area?

3,000 square feet, or about 333 square yards.

Does the stone base count in the asphalt tonnage?

No. The base is ordered separately, usually as crushed stone or road base by the ton. The base calculator handles that part.

What density should I use?

About 145 lb per cubic foot is a common planning figure for compacted hot mix. Your plant may give a slightly different number.

As an Amazon Associate, AsphaltTons.com earns from qualifying purchases. Product links below are sponsored.