How Many Tons of Asphalt for a 36x60 Parking Area?

How many tons of asphalt for a 36x60 parking area: plan on about 26.1 tons at 2 inches compacted or 39.1 tons at 3 inches. Those figures come from 2,160 square feet of surface and a typical compacted density near 145 lb per cubic foot. Your plant’s mix design may run a little heavier or lighter.

Asphalt tonnage calculator →

Step-by-step math for 36x60

Area: 36 ft × 60 ft = 2,160 sq ft.
Thickness in feet: 3 inches ÷ 12 = 0.25 ft.
Volume: 2,160 × 0.25 = 540 cubic feet.
Weight: 540 × 145 lb = 78,300 lb.
Tons: divide by 2,000 = 39.1 tons.

Swap in your own thickness and the plant’s stated density if you have it. The asphalt tonnage calculator runs the same steps.

Tons at common thicknesses

Compacted thickness	Cubic feet	Tons (145 lb/ft³)	Tons +5%
2 in	360	26.1	27.4
2.5 in	450	32.6	34.3
3 in	540	39.1	41.1
4 in	720	52.2	54.8

Choosing a thickness

Residential parking areas are commonly paved at 2 to 3 inches of compacted surface over a compacted stone base. Overlays on sound old pavement are often 1.5 to 2 inches. If heavy trucks, an RV or a delivery vehicle will use the parking area, many contractors step up to 3 or 4 inches total, sometimes as a binder course plus a surface course.

Ordering and trucks

Hot mix is sold by the ton and arrives in dump trucks that commonly haul 10 to 20 tons each. For 39.1 tons at 3 inches, figure roughly 3 loads at about 14 tons apiece. Ask the plant about minimums and the time the mix will hold heat on the haul. See how many tons in a truckload of asphalt for more on load sizes.

Things that change the tonnage

Uneven base. Low spots fill with extra mix. A base that is graded and compacted flat keeps the tonnage close to the math.
Edges and flares. Curved edges, a wider apron at the street or a turnaround add square footage. Measure those separately and add them in.
Density. Mixes typically range from about 140 to 150 lb per compacted cubic foot. Ask your plant for its number if you need tight figures.
Waste. Many estimators add 5 to 10 percent for handling, raking and thickness variation.

Pricing it out

Multiply your tonnage by the per-ton price your local plant or contractor quotes. Installed prices also cover base work, equipment and labor, so material tons are only part of the bid. See asphalt cost per ton for what goes into a quote.

Good and poor uses for asphalt

Best suited to:

Driveways, parking pads and private lanes that need a smooth, sealed surface
Overlays on old pavement that is cracked but still structurally sound
Areas where snow will be plowed, since a paved surface does not throw stone

Less suited to:

Ground that stays soft or wet, unless the base and drainage are fixed first
Very small patches, where bagged cold patch is often simpler
Jobs in cold weather, since hot mix needs warm temperatures to compact properly

Quick reference numbers

Per inch over 100 sq ft: about 0.62 tons of asphalt (0.31 cubic yards).
Per inch over 1,000 sq ft: about 6.2 tons.
Another size for comparison: a 12x24 area at 4 inches takes about 7.1 tons.
Weight used here: about 2.0 tons per cubic yard (roughly 145 lb per compacted cubic foot).

Mistakes that throw off the order

Skipping drainage. Water sitting under any surface softens the base and leads to ruts and potholes.
Forgetting that compaction shrinks loose material. A loose 4-inch spread of a dense-graded stone may finish closer to 3 inches after rolling.
Assuming every supplier uses the same weight. Two yards selling the same product name can quote different tons per yard.
Using inches as if they were feet. Depth has to be divided by 12 before you multiply; skipping that step inflates the order twelvefold.

Questions people ask

How many tons of asphalt for a 36x60 parking area at 2 inches?

About 26.1 tons of compacted asphalt, or around 27.4 tons with a 5 percent allowance.

How many tons for a 36x60 parking area at 3 inches?

About 39.1 tons at 145 lb per cubic foot.

How many square feet is a 36x60 parking area?

2,160 square feet, or about 240 square yards.

Does the stone base count in the asphalt tonnage?

No. The base is ordered separately, usually as crushed stone or road base by the ton. The base calculator handles that part.

What density should I use?

About 145 lb per cubic foot is a common planning figure for compacted hot mix. Your plant may give a slightly different number.

As an Amazon Associate, AsphaltTons.com earns from qualifying purchases. Product links below are sponsored.