How Many Tons of Asphalt for a 40x200 Parking Area?

How many tons of asphalt for a 40x200 parking area comes down to thickness. The area is 40 × 200 = 8,000 square feet. Using a common planning density of about 145 pounds per cubic foot for compacted hot mix, a 2-inch mat needs roughly 96.7 tons and a 3-inch mat roughly 145.0 tons, before any allowance for waste or uneven base.

Asphalt tonnage calculator →

Step-by-step math for 40x200

Area: 40 ft × 200 ft = 8,000 sq ft.
Thickness in feet: 3 inches ÷ 12 = 0.25 ft.
Volume: 8,000 × 0.25 = 2,000 cubic feet.
Weight: 2,000 × 145 lb = 290,000 lb.
Tons: divide by 2,000 = 145.0 tons.

Swap in your own thickness and the plant’s stated density if you have it. The asphalt tonnage calculator runs the same steps.

Tons at common thicknesses

Compacted thickness	Cubic feet	Tons (145 lb/ft³)	Tons +5%
2 in	1,333	96.7	101.5
2.5 in	1,667	120.8	126.9
3 in	2,000	145.0	152.2
4 in	2,667	193.3	203.0

Choosing a thickness

Residential parking areas are commonly paved at 2 to 3 inches of compacted surface over a compacted stone base. Overlays on sound old pavement are often 1.5 to 2 inches. If heavy trucks, an RV or a delivery vehicle will use the parking area, many contractors step up to 3 or 4 inches total, sometimes as a binder course plus a surface course.

Ordering and trucks

Hot mix is sold by the ton and arrives in dump trucks that commonly haul 10 to 20 tons each. For 145.0 tons at 3 inches, figure roughly 11 loads at about 14 tons apiece. Ask the plant about minimums and the time the mix will hold heat on the haul. See how many tons in a truckload of asphalt for more on load sizes.

Things that change the tonnage

Uneven base. Low spots fill with extra mix. A base that is graded and compacted flat keeps the tonnage close to the math.
Edges and flares. Curved edges, a wider apron at the street or a turnaround add square footage. Measure those separately and add them in.
Density. Mixes typically range from about 140 to 150 lb per compacted cubic foot. Ask your plant for its number if you need tight figures.
Waste. Many estimators add 5 to 10 percent for handling, raking and thickness variation.

Pricing it out

Multiply your tonnage by the per-ton price your local plant or contractor quotes. Installed prices also cover base work, equipment and labor, so material tons are only part of the bid. See asphalt cost per ton for what goes into a quote.

Where asphalt fits

Works well for:

Driveways, parking pads and private lanes that need a smooth, sealed surface
Overlays on old pavement that is cracked but still structurally sound
Areas where snow will be plowed, since a paved surface does not throw stone

Think twice for:

Ground that stays soft or wet, unless the base and drainage are fixed first
Very small patches, where bagged cold patch is often simpler
Jobs in cold weather, since hot mix needs warm temperatures to compact properly

Quick reference numbers

Per inch over 100 sq ft: about 0.62 tons of asphalt (0.31 cubic yards).
Per inch over 1,000 sq ft: about 6.2 tons.
Another size for comparison: a 8x16 area at 3 inches takes about 2.4 tons.
Weight used here: about 2.0 tons per cubic yard (roughly 145 lb per compacted cubic foot).

Common estimating mistakes

Measuring only the main rectangle. Aprons, turnouts and curved edges add real square footage.
Forgetting that compaction shrinks loose material. A loose 4-inch spread of a dense-graded stone may finish closer to 3 inches after rolling.
Assuming every supplier uses the same weight. Two yards selling the same product name can quote different tons per yard.
Ordering exactly the math. Uneven ground and spillage nearly always need a little more than the flat calculation.

Questions people ask

How many tons of asphalt for a 40x200 parking area at 2 inches?

About 96.7 tons of compacted asphalt, or around 101.5 tons with a 5 percent allowance.

How many tons for a 40x200 parking area at 3 inches?

About 145.0 tons at 145 lb per cubic foot.

How many square feet is a 40x200 parking area?

8,000 square feet, or about 889 square yards.

Does the stone base count in the asphalt tonnage?

No. The base is ordered separately, usually as crushed stone or road base by the ton. The base calculator handles that part.

What density should I use?

About 145 lb per cubic foot is a common planning figure for compacted hot mix. Your plant may give a slightly different number.

As an Amazon Associate, AsphaltTons.com earns from qualifying purchases. Product links below are sponsored.