How Many Tons of Asphalt for a 9x120 Driveway?

How many tons of asphalt for a 9x120 driveway comes down to thickness. The area is 9 × 120 = 1,080 square feet. Using a common planning density of about 145 pounds per cubic foot for compacted hot mix, a 2-inch mat needs roughly 13.1 tons and a 3-inch mat roughly 19.6 tons, before any allowance for waste or uneven base.

Asphalt tonnage calculator →

Step-by-step math for 9x120

Area: 9 ft × 120 ft = 1,080 sq ft.
Thickness in feet: 3 inches ÷ 12 = 0.25 ft.
Volume: 1,080 × 0.25 = 270 cubic feet.
Weight: 270 × 145 lb = 39,150 lb.
Tons: divide by 2,000 = 19.6 tons.

Swap in your own thickness and the plant’s stated density if you have it. The asphalt tonnage calculator runs the same steps.

Tons at common thicknesses

Compacted thickness	Cubic feet	Tons (145 lb/ft³)	Tons +5%
2 in	180	13.1	13.7
2.5 in	225	16.3	17.1
3 in	270	19.6	20.6
4 in	360	26.1	27.4

What thickness fits this job

Thickness is set by traffic and base. Cars on a well-compacted base get by with 2 to 3 inches. A driveway that sees heavy deliveries or sits on soft soil needs more, either thicker asphalt or a deeper base, and a contractor may split it into two lifts.

Ordering and trucks

Hot mix is sold by the ton and arrives in dump trucks that commonly haul 10 to 20 tons each. For 19.6 tons at 3 inches, figure roughly 2 loads at about 14 tons apiece. Ask the plant about minimums and the time the mix will hold heat on the haul. See how many tons in a truckload of asphalt for more on load sizes.

Things that change the tonnage

Uneven base. Low spots fill with extra mix. A base that is graded and compacted flat keeps the tonnage close to the math.
Edges and flares. Curved edges, a wider apron at the street or a turnaround add square footage. Measure those separately and add them in.
Density. Mixes typically range from about 140 to 150 lb per compacted cubic foot. Ask your plant for its number if you need tight figures.
Waste. Many estimators add 5 to 10 percent for handling, raking and thickness variation.

Pricing it out

Multiply your tonnage by the per-ton price your local plant or contractor quotes. Installed prices also cover base work, equipment and labor, so material tons are only part of the bid. See asphalt cost per ton for what goes into a quote.

Where asphalt fits

Good uses:

Driveways, parking pads and private lanes that need a smooth, sealed surface
Overlays on old pavement that is cracked but still structurally sound
Areas where snow will be plowed, since a paved surface does not throw stone

Think twice for:

Ground that stays soft or wet, unless the base and drainage are fixed first
Very small patches, where bagged cold patch is often simpler
Jobs in cold weather, since hot mix needs warm temperatures to compact properly

Quick reference numbers

Per inch over 100 sq ft: about 0.62 tons of asphalt (0.31 cubic yards).
Per inch over 1,000 sq ft: about 6.2 tons.
Another size for comparison: a 15x30 area at 2 inches takes about 5.6 tons.
Weight used here: about 2.0 tons per cubic yard (roughly 145 lb per compacted cubic foot).

Common estimating mistakes

Skipping drainage. Water sitting under any surface softens the base and leads to ruts and potholes.
Assuming every supplier uses the same weight. Two yards selling the same product name can quote different tons per yard.
Ignoring the base. A thin surface layer over soft soil fails early no matter how much material is on top.
Forgetting that compaction shrinks loose material. A loose 4-inch spread of a dense-graded stone may finish closer to 3 inches after rolling.

Questions people ask

How many tons of asphalt for a 9x120 driveway at 2 inches?

About 13.1 tons of compacted asphalt, or around 13.7 tons with a 5 percent allowance.

How many tons for a 9x120 driveway at 3 inches?

About 19.6 tons at 145 lb per cubic foot.

How many square feet is a 9x120 driveway?

1,080 square feet, or about 120 square yards.

Does the stone base count in the asphalt tonnage?

No. The base is ordered separately, usually as crushed stone or road base by the ton. The base calculator handles that part.

What density should I use?

About 145 lb per cubic foot is a common planning figure for compacted hot mix. Your plant may give a slightly different number.

As an Amazon Associate, AsphaltTons.com earns from qualifying purchases. Product links below are sponsored.