How Much #57 Stone for a 16x80 Driveway?
How much #57 stone for a 16x80 driveway: at 4 inches deep you need about 15.80 cubic yards, which is roughly 21.3 tons at 1.35 tons per yard. The driveway covers 1,280 square feet, so every inch of depth adds about 3.95 yards.
Volume and tonnage calculator →The math for a 16x80 driveway
- Area: 16 × 80 = 1,280 sq ft.
- Depth in feet: 4 ÷ 12 = 0.333 ft.
- Cubic feet: 1,280 × 0.333 = 426.7 cu ft.
- Cubic yards: ÷ 27 = 15.80 yd³.
- Tons: × 1.35 = 21.3 tons.
The volume and tonnage calculator does this for any size.
#57 stone needed by depth
| Depth | Cubic yards | Tons (approx.) | Tons +10% |
|---|---|---|---|
| 2 in | 7.90 | 10.7 | 11.7 |
| 3 in | 11.85 | 16.0 | 17.6 |
| 4 in | 15.80 | 21.3 | 23.5 |
| 6 in | 23.70 | 32.0 | 35.2 |
About #57 stone
#57 stone is a clean crushed stone in roughly the 1/2 to 1 inch range with very few fines. It drains fast, which suits drainage layers and the top of a gravel drive, but it does not pack into a hard crust by itself. Weight per yard is a planning number; the scale ticket at the yard is the real one.
Preparing the driveway
Strip sod and soft topsoil, grade for drainage and compact the subgrade before any stone goes down. Gravel drives last longer with a compacted base layer under the top stone and a slight crown so water runs off. This driveway sees car and truck traffic, so match the depth to that load rather than to the minimum.
Ordering tips
- Round up. Compaction and uneven ground eat material. Adding about 10 percent is common.
- Delivery size. 23.5 tons may take more than one typical dump truck load; small loads may carry a delivery fee. See how many tons of gravel in a dump truck.
- Bulk vs bags. At this size bulk delivery is usually the practical choice.
- Where it drops. Have the truck dump as close to the driveway as firm ground allows.
Good and poor uses for #57 stone
Works well for:
- French drains and drainage layers
- The top course of a gravel driveway
- Under sheds where water needs to drain away
Less suited to:
- A standalone base, since it does not pack hard without fines
- Paver setting beds
- Walk paths meant for strollers or wheelchairs
Quick reference numbers
- Per inch over 100 sq ft: about 0.42 tons of #57 stone (0.31 cubic yards).
- Per inch over 1,000 sq ft: about 4.2 tons.
- Another size for comparison: a 10x20 area at 3 inches takes about 2.5 tons.
- Weight used here: about 1.35 tons per cubic yard.
Common estimating mistakes
- Ignoring the base. A thin surface layer over soft soil fails early no matter how much material is on top.
- Ordering exactly the math. Uneven ground and spillage nearly always need a little more than the flat calculation.
- Mixing up cubic yards and tons. Yards are volume, tons are weight; convert with the product’s weight per yard.
- Skipping drainage. Water sitting under any surface softens the base and leads to ruts and potholes.
Questions people ask
How many tons of #57 stone for a 16x80 driveway?
About 21.3 tons at 4 inches deep, or 23.5 tons with 10 percent extra.
How many cubic yards is a 16x80 driveway at 4 inches?
About 15.80 cubic yards.
How much does a cubic yard of #57 stone weigh?
Usually around 1.3 to 1.45 tons, depending on stone size, fines and moisture.
How deep should #57 stone be for a driveway?
The table above shows 2 to 6 inches. Shallower depths suit top dressing; deeper depths suit new installs and heavier use.
How many square feet is 16x80?
1,280 square feet.
Related guides
- Number 57 Stone: Size, Weight, Uses, and Coverage
- Tons to Cubic Yards for Gravel: Conversion Chart
- How Many Tons of Gravel in a Dump Truck? Loads and Coverage
- How Much Does a Ton of Gravel Cover? Depth Chart
- How Much #57 Stone for a 16x70 Driveway?
- How Much #57 Stone for a 16x75 Driveway?
As an Amazon Associate, AsphaltTons.com earns from qualifying purchases. Product links below are sponsored.