How Much #57 Stone for a 20x14 Patio?
How much #57 stone for a 20x14 patio is a quick volume problem. 280 square feet at 3 inches comes to 2.59 cubic yards. #57 stone usually weighs about 1.3 to 1.45 tons per cubic yard, so plan on roughly 3.5 tons.
Volume and tonnage calculator →The math for a 20x14 patio
- Area: 20 × 14 = 280 sq ft.
- Depth in feet: 3 ÷ 12 = 0.250 ft.
- Cubic feet: 280 × 0.250 = 70.0 cu ft.
- Cubic yards: ÷ 27 = 2.59 yd³.
- Tons: × 1.35 = 3.5 tons.
The volume and tonnage calculator does this for any size.
#57 stone needed by depth
| Depth | Cubic yards | Tons (approx.) | Tons +10% |
|---|---|---|---|
| 2 in | 1.73 | 2.3 | 2.6 |
| 3 in | 2.59 | 3.5 | 3.9 |
| 4 in | 3.46 | 4.7 | 5.1 |
| 6 in | 5.19 | 7.0 | 7.7 |
About #57 stone
Since #57 is washed and open-graded, it moves a little underfoot. Many installers put it over a compacted base of a dense-graded stone rather than straight on soil. If the yard sells by the cubic yard instead of the ton, use the cubic-yard column directly.
Preparing the patio
Remove sod, level the area with a slight slope away from the house, and lay landscape fabric if weeds are a concern. Edging keeps loose material inside the patio footprint. Since the patio carries foot traffic and furniture, a little extra depth is cheap insurance.
Ordering tips
- Round up. Compaction and uneven ground eat material. Adding about 10 percent is common.
- Delivery size. 3.9 tons fits in a single typical dump truck load; small loads may carry a delivery fee. See how many tons of gravel in a dump truck.
- Bulk vs bags. At this size bulk delivery is usually the practical choice.
- Where it drops. Have the truck dump as close to the patio as firm ground allows.
Good and poor uses for #57 stone
Good uses:
- French drains and drainage layers
- The top course of a gravel driveway
- Under sheds where water needs to drain away
Less suited to:
- A standalone base, since it does not pack hard without fines
- Paver setting beds
- Walk paths meant for strollers or wheelchairs
Quick reference numbers
- Per inch over 100 sq ft: about 0.42 tons of #57 stone (0.31 cubic yards).
- Per inch over 1,000 sq ft: about 4.2 tons.
- Another size for comparison: a 15x30 area at 2 inches takes about 3.8 tons.
- Weight used here: about 1.35 tons per cubic yard.
Common estimating mistakes
- Measuring only the main rectangle. Aprons, turnouts and curved edges add real square footage.
- Ordering exactly the math. Uneven ground and spillage nearly always need a little more than the flat calculation.
- Assuming every supplier uses the same weight. Two yards selling the same product name can quote different tons per yard.
- Skipping drainage. Water sitting under any surface softens the base and leads to ruts and potholes.
Questions people ask
How many tons of #57 stone for a 20x14 patio?
About 3.5 tons at 3 inches deep, or 3.9 tons with 10 percent extra.
How many cubic yards is a 20x14 patio at 3 inches?
About 2.59 cubic yards.
How much does a cubic yard of #57 stone weigh?
Usually around 1.3 to 1.45 tons, depending on stone size, fines and moisture.
How deep should #57 stone be for a patio?
The table above shows 2 to 6 inches. Shallower depths suit top dressing; deeper depths suit new installs and heavier use.
How many square feet is 20x14?
280 square feet.
Related guides
- Number 57 Stone: Size, Weight, Uses, and Coverage
- Tons to Cubic Yards for Gravel: Conversion Chart
- How Many Tons of Gravel in a Dump Truck? Loads and Coverage
- How Much Does a Ton of Gravel Cover? Depth Chart
- How Much #57 Stone for a 20x10 Patio?
- How Much #57 Stone for a 20x12 Patio?
As an Amazon Associate, AsphaltTons.com earns from qualifying purchases. Product links below are sponsored.