How Much #57 Stone for a 20x60 Driveway?
How much #57 stone for a 20x60 driveway is a quick volume problem. 1,200 square feet at 4 inches comes to 14.81 cubic yards. #57 stone usually weighs about 1.3 to 1.45 tons per cubic yard, so plan on roughly 20.0 tons.
Volume and tonnage calculator →The math for a 20x60 driveway
- Area: 20 × 60 = 1,200 sq ft.
- Depth in feet: 4 ÷ 12 = 0.333 ft.
- Cubic feet: 1,200 × 0.333 = 400.0 cu ft.
- Cubic yards: ÷ 27 = 14.81 yd³.
- Tons: × 1.35 = 20.0 tons.
The volume and tonnage calculator does this for any size.
#57 stone needed by depth
| Depth | Cubic yards | Tons (approx.) | Tons +10% |
|---|---|---|---|
| 2 in | 7.41 | 10.0 | 11.0 |
| 3 in | 11.11 | 15.0 | 16.5 |
| 4 in | 14.81 | 20.0 | 22.0 |
| 6 in | 22.22 | 30.0 | 33.0 |
About #57 stone
Since #57 is washed and open-graded, it moves a little underfoot. Many installers put it over a compacted base of a dense-graded stone rather than straight on soil. Ask your supplier for their own tons-per-yard figure, since stone source and moisture shift it.
Preparing the driveway
Strip sod and soft topsoil, grade for drainage and compact the subgrade before any stone goes down. Gravel drives last longer with a compacted base layer under the top stone and a slight crown so water runs off. For car and truck traffic, the depths in the table above are a reasonable starting range.
Ordering tips
- Round up. Compaction and uneven ground eat material. Adding about 10 percent is common.
- Delivery size. 22.0 tons may take more than one typical dump truck load; small loads may carry a delivery fee. See how many tons of gravel in a dump truck.
- Bulk vs bags. At this size bulk delivery is usually the practical choice.
- Where it drops. Have the truck dump as close to the driveway as firm ground allows.
Good and poor uses for #57 stone
Works well for:
- French drains and drainage layers
- The top course of a gravel driveway
- Under sheds where water needs to drain away
Think twice for:
- A standalone base, since it does not pack hard without fines
- Paver setting beds
- Walk paths meant for strollers or wheelchairs
Quick reference numbers
- Per inch over 100 sq ft: about 0.42 tons of #57 stone (0.31 cubic yards).
- Per inch over 1,000 sq ft: about 4.2 tons.
- Another size for comparison: a 14x28 area at 2 inches takes about 3.3 tons.
- Weight used here: about 1.35 tons per cubic yard.
Where estimates go wrong
- Forgetting that compaction shrinks loose material. A loose 4-inch spread of a dense-graded stone may finish closer to 3 inches after rolling.
- Measuring only the main rectangle. Aprons, turnouts and curved edges add real square footage.
- Skipping drainage. Water sitting under any surface softens the base and leads to ruts and potholes.
- Assuming every supplier uses the same weight. Two yards selling the same product name can quote different tons per yard.
Questions people ask
How many tons of #57 stone for a 20x60 driveway?
About 20.0 tons at 4 inches deep, or 22.0 tons with 10 percent extra.
How many cubic yards is a 20x60 driveway at 4 inches?
About 14.81 cubic yards.
How much does a cubic yard of #57 stone weigh?
Usually around 1.3 to 1.45 tons, depending on stone size, fines and moisture.
How deep should #57 stone be for a driveway?
The table above shows 2 to 6 inches. Shallower depths suit top dressing; deeper depths suit new installs and heavier use.
How many square feet is 20x60?
1,200 square feet.
Related guides
- Number 57 Stone: Size, Weight, Uses, and Coverage
- Tons to Cubic Yards for Gravel: Conversion Chart
- How Many Tons of Gravel in a Dump Truck? Loads and Coverage
- How Much Does a Ton of Gravel Cover? Depth Chart
- How Much #57 Stone for a 20x45 Driveway?
- How Much #57 Stone for a 20x50 Driveway?
As an Amazon Associate, AsphaltTons.com earns from qualifying purchases. Product links below are sponsored.