How Much Asphalt Millings for 600 Square Feet?
How much asphalt millings for 600 square feet depends on depth. At 4 inches you need about 7.41 cubic yards, roughly 9.6 tons at 1.3 tons per yard. At 3 inches the order drops to 7.2 tons.
Volume and tonnage calculator →Asphalt millings for 600 sq ft by depth
| Depth | Cubic yards | Tons | Tons +10% |
|---|---|---|---|
| 3 in | 5.56 | 7.2 | 7.9 |
| 4 in | 7.41 | 9.6 | 10.6 |
| 6 in | 11.11 | 14.4 | 15.9 |
Working it out
- 600 sq ft × (4 ÷ 12) ft = 200.0 cubic feet.
- ÷ 27 = 7.41 cubic yards.
- × 1.3 tons per yard = 9.6 tons.
About asphalt millings
Millings vary by source: some loads are fine and uniform, others carry chunks. Ask the supplier for a screened product if you want a smoother finish, and check local rules, since some areas restrict their use near water. Expect the weight to fall in the range of 1.2 to 1.4 loose tons per yard.
Ordering checklist
- Measure odd shapes in pieces. Split curves and L-shapes into rectangles and add them.
- Add a margin. About 10 percent covers compaction and low spots.
- Bulk or bags. Bulk delivery is the practical choice here.
- Prep first. Remove sod, compact the subgrade and set edging before the stone arrives.
Use the volume and tonnage calculator for any other size.
Good and poor uses for asphalt millings
Good uses:
- Rural driveways and farm lanes
- Parking areas where a dust-free surface is wanted
- Low-cost base under a future paved surface
Think twice for:
- Areas near wells or streams where local rules limit them
- Decorative or barefoot areas
- Jobs needing a uniform, clean look
Quick reference numbers
- Per inch over 100 sq ft: about 0.40 tons of asphalt millings (0.31 cubic yards).
- Per inch over 1,000 sq ft: about 4.0 tons.
- Another size for comparison: a 8x16 area at 3 inches takes about 1.5 tons.
- Weight used here: about 1.3 tons per cubic yard.
Common estimating mistakes
- Skipping drainage. Water sitting under any surface softens the base and leads to ruts and potholes.
- Measuring only the main rectangle. Aprons, turnouts and curved edges add real square footage.
- Forgetting that compaction shrinks loose material. A loose 4-inch spread of a dense-graded stone may finish closer to 3 inches after rolling.
- Ignoring the base. A thin surface layer over soft soil fails early no matter how much material is on top.
Questions people ask
How many tons of asphalt millings for 600 square feet?
About 9.6 tons at 4 inches deep.
How many cubic yards of asphalt millings for 600 square feet?
About 7.41 yards at 4 inches.
How much asphalt millings for 600 square feet at 3 inches?
About 7.2 tons, or 5.56 cubic yards.
How much does a yard of asphalt millings weigh?
About 1.2 to 1.4 loose tons.
Should I add extra?
Yes, about 10 percent is a common allowance.
Related guides
- How Many Tons of Asphalt Millings for a 40x25 Area?
- Tons to Cubic Yards for Gravel: Conversion Chart
- How Much Does a Ton of Gravel Cover? Depth Chart
- How Much Asphalt Millings for 400 Square Feet?
- How Much Asphalt Millings for 500 Square Feet?
As an Amazon Associate, AsphaltTons.com earns from qualifying purchases. Product links below are sponsored.