How Much Asphalt Millings for a 16x30 Parking Pad?

How much asphalt millings for a 16x30 parking pad: at 4 inches deep you need about 5.93 cubic yards, which is roughly 7.7 tons at 1.3 tons per yard. The parking pad covers 480 square feet, so every inch of depth adds about 1.48 yards.

Volume and tonnage calculator →

The math for a 16x30 parking pad

Area: 16 × 30 = 480 sq ft.
Depth in feet: 4 ÷ 12 = 0.333 ft.
Cubic feet: 480 × 0.333 = 160.0 cu ft.
Cubic yards: ÷ 27 = 5.93 yd³.
Tons: × 1.3 = 7.7 tons.

The volume and tonnage calculator does this for any size.

Asphalt millings needed by depth

Depth	Cubic yards	Tons (approx.)	Tons +10%
3 in	4.44	5.8	6.4
4 in	5.93	7.7	8.5
6 in	8.89	11.6	12.7

About asphalt millings

Asphalt millings are ground-up old pavement. When compacted and warmed by sun they bind into a fairly firm surface, which is why they are popular for rural drives and lots. If the yard sells by the cubic yard instead of the ton, use the cubic-yard column directly.

Preparing the parking pad

Dig out organic soil, compact the subgrade and set an edge so the stone does not migrate onto the lawn. A pad that holds parked weight for long periods benefits from a dense base under the surface stone. Since the parking pad carries parked vehicles, a little extra depth is cheap insurance.

Ordering tips

Round up. Compaction and uneven ground eat material. Adding about 10 percent is common.
Delivery size. 8.5 tons fits in a single typical dump truck load; small loads may carry a delivery fee. See how many tons of gravel in a dump truck.
Bulk vs bags. At this size bulk delivery is usually the practical choice.
Where it drops. Have the truck dump as close to the parking pad as firm ground allows.

When to choose asphalt millings

Good uses:

Rural driveways and farm lanes
Parking areas where a dust-free surface is wanted
Low-cost base under a future paved surface

Less suited to:

Areas near wells or streams where local rules limit them
Decorative or barefoot areas
Jobs needing a uniform, clean look

Quick reference numbers

Per inch over 100 sq ft: about 0.40 tons of asphalt millings (0.31 cubic yards).
Per inch over 1,000 sq ft: about 4.0 tons.
Another size for comparison: a 8x16 area at 4 inches takes about 2.1 tons.
Weight used here: about 1.3 tons per cubic yard.

Mistakes that throw off the order

Mixing up cubic yards and tons. Yards are volume, tons are weight; convert with the product’s weight per yard.
Using inches as if they were feet. Depth has to be divided by 12 before you multiply; skipping that step inflates the order twelvefold.
Assuming every supplier uses the same weight. Two yards selling the same product name can quote different tons per yard.
Skipping drainage. Water sitting under any surface softens the base and leads to ruts and potholes.

Questions people ask

How many tons of asphalt millings for a 16x30 parking pad?

About 7.7 tons at 4 inches deep, or 8.5 tons with 10 percent extra.

How many cubic yards is a 16x30 parking pad at 4 inches?

About 5.93 cubic yards.

How much does a cubic yard of asphalt millings weigh?

Usually around 1.2 to 1.4 loose tons, depending on stone size, fines and moisture.

How deep should asphalt millings be for a parking pad?

The table above shows 3 to 6 inches. Shallower depths suit top dressing; deeper depths suit new installs and heavier use.

How many square feet is 16x30?

480 square feet.

As an Amazon Associate, AsphaltTons.com earns from qualifying purchases. Product links below are sponsored.