How Much Road Base for a 14x8 Shed Base?
A 14 by 8 foot shed base is 112 square feet. How much road base for a 14x8 shed base depends on depth: at 4 inches it is about 1.38 cubic yards or 2.1 tons. Suppliers usually sell by the ton, so the tonnage is the number to give them.
Volume and tonnage calculator →The math for a 14x8 shed base
- Area: 14 × 8 = 112 sq ft.
- Depth in feet: 4 ÷ 12 = 0.333 ft.
- Cubic feet: 112 × 0.333 = 37.3 cu ft.
- Cubic yards: ÷ 27 = 1.38 yd³.
- Tons: × 1.5 = 2.1 tons.
The volume and tonnage calculator does this for any size.
Road base needed by depth
| Depth | Cubic yards | Tons (approx.) | Tons +10% |
|---|---|---|---|
| 4 in | 1.38 | 2.1 | 2.3 |
| 6 in | 2.07 | 3.1 | 3.4 |
| 8 in | 2.77 | 4.1 | 4.6 |
About road base
Road base is meant to be compacted at close to the right moisture. Dry base rock does not lock up well; a light spray of water before rolling helps. Ask your supplier for their own tons-per-yard figure, since stone source and moisture shift it.
Preparing the shed base
Level the footprint, extend the stone a foot or so beyond the shed walls for drip and drainage, and compact in lifts. A timber or block border holds the pad shape. For a shed floor frame, the depths in the table above are a reasonable starting range.
Ordering tips
- Round up. Compaction and uneven ground eat material. Adding about 10 percent is common.
- Delivery size. 2.3 tons fits in a single typical dump truck load; small loads may carry a delivery fee. See how many tons of gravel in a dump truck.
- Bulk vs bags. At this size bulk delivery is usually the practical choice.
- Where it drops. Have the truck dump as close to the shed base as firm ground allows.
Good and poor uses for road base
Good uses:
- Base under asphalt and concrete
- Gravel roads and drives
- Equipment and shed pads
Think twice for:
- Drainage layers
- Decorative surfaces
- Surfaces that will stay uncompacted
Quick reference numbers
- Per inch over 100 sq ft: about 0.46 tons of road base (0.31 cubic yards).
- Per inch over 1,000 sq ft: about 4.6 tons.
- Another size for comparison: a 10x20 area at 2 inches takes about 1.9 tons.
- Weight used here: about 1.5 tons per cubic yard.
Mistakes that throw off the order
- Using inches as if they were feet. Depth has to be divided by 12 before you multiply; skipping that step inflates the order twelvefold.
- Ordering exactly the math. Uneven ground and spillage nearly always need a little more than the flat calculation.
- Measuring only the main rectangle. Aprons, turnouts and curved edges add real square footage.
- Forgetting that compaction shrinks loose material. A loose 4-inch spread of a dense-graded stone may finish closer to 3 inches after rolling.
Questions people ask
How many tons of road base for a 14x8 shed base?
About 2.1 tons at 4 inches deep, or 2.3 tons with 10 percent extra.
How many cubic yards is a 14x8 shed base at 4 inches?
About 1.38 cubic yards.
How much does a cubic yard of road base weigh?
Usually around 1.4 to 1.65 compacted tons, depending on stone size, fines and moisture.
How deep should road base be for a shed base?
The table above shows 4 to 8 inches. Shallower depths suit top dressing; deeper depths suit new installs and heavier use.
How many square feet is 14x8?
112 square feet.
Related guides
- Crushed Stone vs Gravel: Differences and Best Uses
- Tons to Cubic Yards for Gravel: Conversion Chart
- How Many Tons of Gravel in a Dump Truck? Loads and Coverage
- How Much Does a Ton of Gravel Cover? Depth Chart
- How Much Road Base for a 12x20 Shed Base?
- How Much Road Base for a 12x24 Shed Base?
As an Amazon Associate, AsphaltTons.com earns from qualifying purchases. Product links below are sponsored.