How Much Road Base for a 16x45 Driveway?
How much road base for a 16x45 driveway is a quick volume problem. 720 square feet at 4 inches comes to 8.89 cubic yards. Road base usually weighs about 1.4 to 1.65 compacted tons per cubic yard, so plan on roughly 13.3 tons.
Volume and tonnage calculator →The math for a 16x45 driveway
- Area: 16 × 45 = 720 sq ft.
- Depth in feet: 4 ÷ 12 = 0.333 ft.
- Cubic feet: 720 × 0.333 = 240.0 cu ft.
- Cubic yards: ÷ 27 = 8.89 yd³.
- Tons: × 1.5 = 13.3 tons.
The volume and tonnage calculator does this for any size.
Road base needed by depth
| Depth | Cubic yards | Tons (approx.) | Tons +10% |
|---|---|---|---|
| 4 in | 8.89 | 13.3 | 14.7 |
| 6 in | 13.33 | 20.0 | 22.0 |
| 8 in | 17.78 | 26.7 | 29.3 |
About road base
Road base is meant to be compacted at close to the right moisture. Dry base rock does not lock up well; a light spray of water before rolling helps. If the yard sells by the cubic yard instead of the ton, use the cubic-yard column directly.
Preparing the driveway
Strip sod and soft topsoil, grade for drainage and compact the subgrade before any stone goes down. Gravel drives last longer with a compacted base layer under the top stone and a slight crown so water runs off. For car and truck traffic, the depths in the table above are a reasonable starting range.
Ordering tips
- Round up. Compaction and uneven ground eat material. Adding about 10 percent is common.
- Delivery size. 14.7 tons may take more than one typical dump truck load; small loads may carry a delivery fee. See how many tons of gravel in a dump truck.
- Bulk vs bags. At this size bulk delivery is usually the practical choice.
- Where it drops. Have the truck dump as close to the driveway as firm ground allows.
Good and poor uses for road base
Best suited to:
- Base under asphalt and concrete
- Gravel roads and drives
- Equipment and shed pads
Think twice for:
- Drainage layers
- Decorative surfaces
- Surfaces that will stay uncompacted
Quick reference numbers
- Per inch over 100 sq ft: about 0.46 tons of road base (0.31 cubic yards).
- Per inch over 1,000 sq ft: about 4.6 tons.
- Another size for comparison: a 10x20 area at 3 inches takes about 2.8 tons.
- Weight used here: about 1.5 tons per cubic yard.
Where estimates go wrong
- Forgetting that compaction shrinks loose material. A loose 4-inch spread of a dense-graded stone may finish closer to 3 inches after rolling.
- Skipping drainage. Water sitting under any surface softens the base and leads to ruts and potholes.
- Measuring only the main rectangle. Aprons, turnouts and curved edges add real square footage.
- Using inches as if they were feet. Depth has to be divided by 12 before you multiply; skipping that step inflates the order twelvefold.
Questions people ask
How many tons of road base for a 16x45 driveway?
About 13.3 tons at 4 inches deep, or 14.7 tons with 10 percent extra.
How many cubic yards is a 16x45 driveway at 4 inches?
About 8.89 cubic yards.
How much does a cubic yard of road base weigh?
Usually around 1.4 to 1.65 compacted tons, depending on stone size, fines and moisture.
How deep should road base be for a driveway?
The table above shows 4 to 8 inches. Shallower depths suit top dressing; deeper depths suit new installs and heavier use.
How many square feet is 16x45?
720 square feet.
Related guides
- Crushed Stone vs Gravel: Differences and Best Uses
- Tons to Cubic Yards for Gravel: Conversion Chart
- How Many Tons of Gravel in a Dump Truck? Loads and Coverage
- How Much Does a Ton of Gravel Cover? Depth Chart
- How Much Road Base for a 16x35 Driveway?
- How Much Road Base for a 16x40 Driveway?
As an Amazon Associate, AsphaltTons.com earns from qualifying purchases. Product links below are sponsored.