How Much Crushed Stone for a 22x100 Driveway?
A 22 by 100 foot driveway is 2,200 square feet. How much crushed stone for a 22x100 driveway depends on depth: at 4 inches it is about 27.16 cubic yards or 38.0 tons. Suppliers usually sell by the ton, so the tonnage is the number to give them.
Volume and tonnage calculator →The math for a 22x100 driveway
- Area: 22 × 100 = 2,200 sq ft.
- Depth in feet: 4 ÷ 12 = 0.333 ft.
- Cubic feet: 2,200 × 0.333 = 733.3 cu ft.
- Cubic yards: ÷ 27 = 27.16 yd³.
- Tons: × 1.4 = 38.0 tons.
The volume and tonnage calculator does this for any size.
Crushed stone needed by depth
| Depth | Cubic yards | Tons (approx.) | Tons +10% |
|---|---|---|---|
| 2 in | 13.58 | 19.0 | 20.9 |
| 3 in | 20.37 | 28.5 | 31.4 |
| 4 in | 27.16 | 38.0 | 41.8 |
| 6 in | 40.74 | 57.0 | 62.7 |
About crushed stone
Crushed stone has fractured faces, so the pieces interlock when compacted. That is why it holds a driveway or pad shape better than round stone of the same size. If the yard sells by the cubic yard instead of the ton, use the cubic-yard column directly.
Preparing the driveway
Strip sod and soft topsoil, grade for drainage and compact the subgrade before any stone goes down. Gravel drives last longer with a compacted base layer under the top stone and a slight crown so water runs off. Since the driveway carries car and truck traffic, a little extra depth is cheap insurance.
Ordering tips
- Round up. Compaction and uneven ground eat material. Adding about 10 percent is common.
- Delivery size. 41.8 tons may take more than one typical dump truck load; small loads may carry a delivery fee. See how many tons of gravel in a dump truck.
- Bulk vs bags. At this size bulk delivery is usually the practical choice.
- Where it drops. Have the truck dump as close to the driveway as firm ground allows.
When to choose crushed stone
Works well for:
- Driveway top courses and parking pads
- Shed and hot tub bases
- Backfill behind walls when a clean size is used
Think twice for:
- Barefoot areas, since angular stone is rough
- Play areas
- Places that need a smooth rolling surface for wheels
Quick reference numbers
- Per inch over 100 sq ft: about 0.43 tons of crushed stone (0.31 cubic yards).
- Per inch over 1,000 sq ft: about 4.3 tons.
- Another size for comparison: a 12x24 area at 2 inches takes about 2.5 tons.
- Weight used here: about 1.4 tons per cubic yard.
Mistakes that throw off the order
- Forgetting that compaction shrinks loose material. A loose 4-inch spread of a dense-graded stone may finish closer to 3 inches after rolling.
- Skipping drainage. Water sitting under any surface softens the base and leads to ruts and potholes.
- Mixing up cubic yards and tons. Yards are volume, tons are weight; convert with the product’s weight per yard.
- Ordering exactly the math. Uneven ground and spillage nearly always need a little more than the flat calculation.
Questions people ask
How many tons of crushed stone for a 22x100 driveway?
About 38.0 tons at 4 inches deep, or 41.8 tons with 10 percent extra.
How many cubic yards is a 22x100 driveway at 4 inches?
About 27.16 cubic yards.
How much does a cubic yard of crushed stone weigh?
Usually around 1.35 to 1.5 tons, depending on stone size, fines and moisture.
How deep should crushed stone be for a driveway?
The table above shows 2 to 6 inches. Shallower depths suit top dressing; deeper depths suit new installs and heavier use.
How many square feet is 22x100?
2,200 square feet.
Related guides
- How Much Does a Ton of Crushed Stone Cover?
- Tons to Cubic Yards for Gravel: Conversion Chart
- How Many Tons of Gravel in a Dump Truck? Loads and Coverage
- How Much Does a Ton of Gravel Cover? Depth Chart
- How Much Crushed Stone for a 22x80 Driveway?
- How Much Crushed Stone for a 22x90 Driveway?
As an Amazon Associate, AsphaltTons.com earns from qualifying purchases. Product links below are sponsored.