How Much Crushed Stone for a 8x8 Shed Base?
How much crushed stone for a 8x8 shed base is a quick volume problem. 64 square feet at 4 inches comes to 0.79 cubic yards. Crushed stone usually weighs about 1.35 to 1.5 tons per cubic yard, so plan on roughly 1.1 tons.
Volume and tonnage calculator →The math for a 8x8 shed base
- Area: 8 × 8 = 64 sq ft.
- Depth in feet: 4 ÷ 12 = 0.333 ft.
- Cubic feet: 64 × 0.333 = 21.3 cu ft.
- Cubic yards: ÷ 27 = 0.79 yd³.
- Tons: × 1.4 = 1.1 tons.
The volume and tonnage calculator does this for any size.
Crushed stone needed by depth
| Depth | Cubic yards | Tons (approx.) | Tons +10% |
|---|---|---|---|
| 2 in | 0.40 | 0.6 | 0.6 |
| 3 in | 0.59 | 0.8 | 0.9 |
| 4 in | 0.79 | 1.1 | 1.2 |
| 6 in | 1.19 | 1.7 | 1.8 |
About crushed stone
Most quarries sell crushed stone by a size number or a screen size. Clean crushed stone drains well; stone with fines packs harder but sheds water more slowly. If the yard sells by the cubic yard instead of the ton, use the cubic-yard column directly.
Preparing the shed base
Level the footprint, extend the stone a foot or so beyond the shed walls for drip and drainage, and compact in lifts. A timber or block border holds the pad shape. For a shed floor frame, the depths in the table above are a reasonable starting range.
Ordering tips
- Round up. Compaction and uneven ground eat material. Adding about 10 percent is common.
- Delivery size. 1.2 tons fits in a single typical dump truck load; small loads may carry a delivery fee. See how many tons of gravel in a dump truck.
- Bulk vs bags. At about 1.1 tons this job is small enough that bagged material could work; a 0.5 cubic foot bag holds about 1/54 of a yard, so compare the bag count with a bulk minimum.
- Where it drops. Have the truck dump as close to the shed base as firm ground allows.
Where crushed stone fits
Good uses:
- Driveway top courses and parking pads
- Shed and hot tub bases
- Backfill behind walls when a clean size is used
Poor fit for:
- Barefoot areas, since angular stone is rough
- Play areas
- Places that need a smooth rolling surface for wheels
Quick reference numbers
- Per inch over 100 sq ft: about 0.43 tons of crushed stone (0.31 cubic yards).
- Per inch over 1,000 sq ft: about 4.3 tons.
- Another size for comparison: a 15x30 area at 3 inches takes about 5.8 tons.
- Weight used here: about 1.4 tons per cubic yard.
Mistakes that throw off the order
- Skipping drainage. Water sitting under any surface softens the base and leads to ruts and potholes.
- Ordering exactly the math. Uneven ground and spillage nearly always need a little more than the flat calculation.
- Forgetting that compaction shrinks loose material. A loose 4-inch spread of a dense-graded stone may finish closer to 3 inches after rolling.
- Using inches as if they were feet. Depth has to be divided by 12 before you multiply; skipping that step inflates the order twelvefold.
Questions people ask
How many tons of crushed stone for a 8x8 shed base?
About 1.1 tons at 4 inches deep, or 1.2 tons with 10 percent extra.
How many cubic yards is a 8x8 shed base at 4 inches?
About 0.79 cubic yards.
How much does a cubic yard of crushed stone weigh?
Usually around 1.35 to 1.5 tons, depending on stone size, fines and moisture.
How deep should crushed stone be for a shed base?
The table above shows 2 to 6 inches. Shallower depths suit top dressing; deeper depths suit new installs and heavier use.
How many square feet is 8x8?
64 square feet.
Related guides
- How Much Does a Ton of Crushed Stone Cover?
- Tons to Cubic Yards for Gravel: Conversion Chart
- How Many Tons of Gravel in a Dump Truck? Loads and Coverage
- How Much Does a Ton of Gravel Cover? Depth Chart
- How Much Crushed Stone for a 6x20 Shed Base?
- How Much Crushed Stone for a 6x24 Shed Base?
As an Amazon Associate, AsphaltTons.com earns from qualifying purchases. Product links below are sponsored.