How Much Crusher Run for 150 Square Feet?
How much crusher run for 150 square feet depends on depth. At 6 inches you need about 2.78 cubic yards, roughly 4.3 tons at 1.55 tons per yard. Going to 8 inches raises it to 5.7 tons.
Volume and tonnage calculator →Crusher run for 150 sq ft by depth
| Depth | Cubic yards | Tons | Tons +10% |
|---|---|---|---|
| 3 in | 1.39 | 2.2 | 2.4 |
| 4 in | 1.85 | 2.9 | 3.2 |
| 6 in | 2.78 | 4.3 | 4.7 |
| 8 in | 3.70 | 5.7 | 6.3 |
Working it out
- 150 sq ft × (6 ÷ 12) ft = 75.0 cubic feet.
- ÷ 27 = 2.78 cubic yards.
- × 1.55 tons per yard = 4.3 tons.
About crusher run
Crusher run (also sold as crush and run, dense-grade aggregate or QP in some regions) mixes stone with stone dust. It compacts into a firm, nearly solid layer, which makes it the usual base under pavers, asphalt and gravel drives. Typical weight: 1.5 to 1.7 compacted tons per cubic yard.
Ordering checklist
- Measure odd shapes in pieces. Split curves and L-shapes into rectangles and add them.
- Add a margin. About 10 percent covers compaction and low spots.
- Bulk or bags. Bulk delivery is the practical choice here.
- Prep first. Remove sod, compact the subgrade and set edging before the stone arrives.
Use the volume and tonnage calculator for any other size.
When to choose crusher run
Works well for:
- Base under asphalt, pavers or concrete
- Gravel drives that need a firm, packed surface
- Shed pads and equipment pads
Poor fit for:
- Drainage layers, since the fines slow water
- Decorative beds
- Spots where you want water to soak straight through
Quick reference numbers
- Per inch over 100 sq ft: about 0.48 tons of crusher run (0.31 cubic yards).
- Per inch over 1,000 sq ft: about 4.8 tons.
- Another size for comparison: a 10x20 area at 4 inches takes about 3.8 tons.
- Weight used here: about 1.55 tons per cubic yard.
Mistakes that throw off the order
- Using inches as if they were feet. Depth has to be divided by 12 before you multiply; skipping that step inflates the order twelvefold.
- Mixing up cubic yards and tons. Yards are volume, tons are weight; convert with the product’s weight per yard.
- Forgetting that compaction shrinks loose material. A loose 4-inch spread of a dense-graded stone may finish closer to 3 inches after rolling.
- Assuming every supplier uses the same weight. Two yards selling the same product name can quote different tons per yard.
Questions people ask
How many tons of crusher run for 150 square feet?
About 4.3 tons at 6 inches deep.
How many cubic yards of crusher run for 150 square feet?
About 2.78 yards at 6 inches.
How much crusher run for 150 square feet at 3 inches?
About 2.2 tons, or 1.39 cubic yards.
How much does a yard of crusher run weigh?
About 1.5 to 1.7 compacted tons.
Should I add extra?
Yes, about 10 percent is a common allowance.
Related guides
- Crushed Stone vs Gravel: Differences and Best Uses
- Tons to Cubic Yards for Gravel: Conversion Chart
- How Much Does a Ton of Gravel Cover? Depth Chart
- How Much Crusher Run for 100 Square Feet?
As an Amazon Associate, AsphaltTons.com earns from qualifying purchases. Product links below are sponsored.