How Much Crusher Run for 2,500 Square Feet?
How much crusher run for 2,500 square feet depends on depth. At 6 inches you need about 46.30 cubic yards, roughly 71.8 tons at 1.55 tons per yard. Going to 8 inches raises it to 95.7 tons.
Volume and tonnage calculator →Crusher run for 2,500 sq ft by depth
| Depth | Cubic yards | Tons | Tons +10% |
|---|---|---|---|
| 3 in | 23.15 | 35.9 | 39.5 |
| 4 in | 30.86 | 47.8 | 52.6 |
| 6 in | 46.30 | 71.8 | 78.9 |
| 8 in | 61.73 | 95.7 | 105.2 |
Working it out
- 2,500 sq ft × (6 ÷ 12) ft = 1,250.0 cubic feet.
- ÷ 27 = 46.30 cubic yards.
- × 1.55 tons per yard = 71.8 tons.
About crusher run
Crusher run (also sold as crush and run, dense-grade aggregate or QP in some regions) mixes stone with stone dust. It compacts into a firm, nearly solid layer, which makes it the usual base under pavers, asphalt and gravel drives. Typical weight: 1.5 to 1.7 compacted tons per cubic yard.
Getting the order right
- Measure odd shapes in pieces. Split curves and L-shapes into rectangles and add them.
- Add a margin. About 10 percent covers compaction and low spots.
- Bulk or bags. Bulk delivery is the practical choice here.
- Prep first. Remove sod, compact the subgrade and set edging before the stone arrives.
Use the volume and tonnage calculator for any other size.
Where crusher run fits
Good uses:
- Base under asphalt, pavers or concrete
- Gravel drives that need a firm, packed surface
- Shed pads and equipment pads
Poor fit for:
- Drainage layers, since the fines slow water
- Decorative beds
- Spots where you want water to soak straight through
Quick reference numbers
- Per inch over 100 sq ft: about 0.48 tons of crusher run (0.31 cubic yards).
- Per inch over 1,000 sq ft: about 4.8 tons.
- Another size for comparison: a 10x20 area at 2 inches takes about 1.9 tons.
- Weight used here: about 1.55 tons per cubic yard.
Where estimates go wrong
- Assuming every supplier uses the same weight. Two yards selling the same product name can quote different tons per yard.
- Forgetting that compaction shrinks loose material. A loose 4-inch spread of a dense-graded stone may finish closer to 3 inches after rolling.
- Mixing up cubic yards and tons. Yards are volume, tons are weight; convert with the product’s weight per yard.
- Ordering exactly the math. Uneven ground and spillage nearly always need a little more than the flat calculation.
Questions people ask
How many tons of crusher run for 2,500 square feet?
About 71.8 tons at 6 inches deep.
How many cubic yards of crusher run for 2,500 square feet?
About 46.30 yards at 6 inches.
How much crusher run for 2,500 square feet at 3 inches?
About 35.9 tons, or 23.15 cubic yards.
How much does a yard of crusher run weigh?
About 1.5 to 1.7 compacted tons.
Should I add extra?
Yes, about 10 percent is a common allowance.
Related guides
- Crushed Stone vs Gravel: Differences and Best Uses
- Tons to Cubic Yards for Gravel: Conversion Chart
- How Much Does a Ton of Gravel Cover? Depth Chart
- How Much Crusher Run for 1,500 Square Feet?
- How Much Crusher Run for 2,000 Square Feet?
As an Amazon Associate, AsphaltTons.com earns from qualifying purchases. Product links below are sponsored.