How Much Crusher Run for a 10x24 Patio?
How much crusher run for a 10x24 patio: at 3 inches deep you need about 2.22 cubic yards, which is roughly 3.4 tons at 1.55 tons per yard. The patio covers 240 square feet, so every inch of depth adds about 0.74 yards.
Volume and tonnage calculator →The math for a 10x24 patio
- Area: 10 × 24 = 240 sq ft.
- Depth in feet: 3 ÷ 12 = 0.250 ft.
- Cubic feet: 240 × 0.250 = 60.0 cu ft.
- Cubic yards: ÷ 27 = 2.22 yd³.
- Tons: × 1.55 = 3.4 tons.
The volume and tonnage calculator does this for any size.
Crusher run needed by depth
| Depth | Cubic yards | Tons (approx.) | Tons +10% |
|---|---|---|---|
| 3 in | 2.22 | 3.4 | 3.8 |
| 4 in | 2.96 | 4.6 | 5.1 |
| 6 in | 4.44 | 6.9 | 7.6 |
| 8 in | 5.93 | 9.2 | 10.1 |
About crusher run
Crusher run (also sold as crush and run, dense-grade aggregate or QP in some regions) mixes stone with stone dust. It compacts into a firm, nearly solid layer, which makes it the usual base under pavers, asphalt and gravel drives. Ask your supplier for their own tons-per-yard figure, since stone source and moisture shift it.
Preparing the patio
Remove sod, level the area with a slight slope away from the house, and lay landscape fabric if weeds are a concern. Edging keeps loose material inside the patio footprint. For foot traffic and furniture, the depths in the table above are a reasonable starting range.
Ordering tips
- Round up. Compaction and uneven ground eat material. Adding about 10 percent is common.
- Delivery size. 3.8 tons fits in a single typical dump truck load; small loads may carry a delivery fee. See how many tons of gravel in a dump truck.
- Bulk vs bags. At this size bulk delivery is usually the practical choice.
- Where it drops. Have the truck dump as close to the patio as firm ground allows.
Good and poor uses for crusher run
Best suited to:
- Base under asphalt, pavers or concrete
- Gravel drives that need a firm, packed surface
- Shed pads and equipment pads
Think twice for:
- Drainage layers, since the fines slow water
- Decorative beds
- Spots where you want water to soak straight through
Quick reference numbers
- Per inch over 100 sq ft: about 0.48 tons of crusher run (0.31 cubic yards).
- Per inch over 1,000 sq ft: about 4.8 tons.
- Another size for comparison: a 10x20 area at 4 inches takes about 3.8 tons.
- Weight used here: about 1.55 tons per cubic yard.
Where estimates go wrong
- Mixing up cubic yards and tons. Yards are volume, tons are weight; convert with the product’s weight per yard.
- Forgetting that compaction shrinks loose material. A loose 4-inch spread of a dense-graded stone may finish closer to 3 inches after rolling.
- Assuming every supplier uses the same weight. Two yards selling the same product name can quote different tons per yard.
- Measuring only the main rectangle. Aprons, turnouts and curved edges add real square footage.
Questions people ask
How many tons of crusher run for a 10x24 patio?
About 3.4 tons at 3 inches deep, or 3.8 tons with 10 percent extra.
How many cubic yards is a 10x24 patio at 3 inches?
About 2.22 cubic yards.
How much does a cubic yard of crusher run weigh?
Usually around 1.5 to 1.7 compacted tons, depending on stone size, fines and moisture.
How deep should crusher run be for a patio?
The table above shows 3 to 8 inches. Shallower depths suit top dressing; deeper depths suit new installs and heavier use.
How many square feet is 10x24?
240 square feet.
Related guides
- Crushed Stone vs Gravel: Differences and Best Uses
- Tons to Cubic Yards for Gravel: Conversion Chart
- How Many Tons of Gravel in a Dump Truck? Loads and Coverage
- How Much Does a Ton of Gravel Cover? Depth Chart
- How Much Crusher Run for a 10x18 Patio?
- How Much Crusher Run for a 10x20 Patio?
As an Amazon Associate, AsphaltTons.com earns from qualifying purchases. Product links below are sponsored.