How Much Crusher Run for a 14x10 Patio?
How much crusher run for a 14x10 patio: at 3 inches deep you need about 1.30 cubic yards, which is roughly 2.0 tons at 1.55 tons per yard. The patio covers 140 square feet, so every inch of depth adds about 0.43 yards.
Volume and tonnage calculator →The math for a 14x10 patio
- Area: 14 × 10 = 140 sq ft.
- Depth in feet: 3 ÷ 12 = 0.250 ft.
- Cubic feet: 140 × 0.250 = 35.0 cu ft.
- Cubic yards: ÷ 27 = 1.30 yd³.
- Tons: × 1.55 = 2.0 tons.
The volume and tonnage calculator does this for any size.
Crusher run needed by depth
| Depth | Cubic yards | Tons (approx.) | Tons +10% |
|---|---|---|---|
| 3 in | 1.30 | 2.0 | 2.2 |
| 4 in | 1.73 | 2.7 | 2.9 |
| 6 in | 2.59 | 4.0 | 4.4 |
| 8 in | 3.46 | 5.4 | 5.9 |
About crusher run
The fines in crusher run fill the gaps between stones, so it weighs more per yard than clean stone once compacted. Plan on rolling or plate-compacting it in lifts. If the yard sells by the cubic yard instead of the ton, use the cubic-yard column directly.
Preparing the patio
Remove sod, level the area with a slight slope away from the house, and lay landscape fabric if weeds are a concern. Edging keeps loose material inside the patio footprint. Since the patio carries foot traffic and furniture, a little extra depth is cheap insurance.
Ordering tips
- Round up. Compaction and uneven ground eat material. Adding about 10 percent is common.
- Delivery size. 2.2 tons fits in a single typical dump truck load; small loads may carry a delivery fee. See how many tons of gravel in a dump truck.
- Bulk vs bags. At this size bulk delivery is usually the practical choice.
- Where it drops. Have the truck dump as close to the patio as firm ground allows.
Good and poor uses for crusher run
Best suited to:
- Base under asphalt, pavers or concrete
- Gravel drives that need a firm, packed surface
- Shed pads and equipment pads
Think twice for:
- Drainage layers, since the fines slow water
- Decorative beds
- Spots where you want water to soak straight through
Quick reference numbers
- Per inch over 100 sq ft: about 0.48 tons of crusher run (0.31 cubic yards).
- Per inch over 1,000 sq ft: about 4.8 tons.
- Another size for comparison: a 10x20 area at 3 inches takes about 2.9 tons.
- Weight used here: about 1.55 tons per cubic yard.
Mistakes that throw off the order
- Ignoring the base. A thin surface layer over soft soil fails early no matter how much material is on top.
- Using inches as if they were feet. Depth has to be divided by 12 before you multiply; skipping that step inflates the order twelvefold.
- Skipping drainage. Water sitting under any surface softens the base and leads to ruts and potholes.
- Forgetting that compaction shrinks loose material. A loose 4-inch spread of a dense-graded stone may finish closer to 3 inches after rolling.
Questions people ask
How many tons of crusher run for a 14x10 patio?
About 2.0 tons at 3 inches deep, or 2.2 tons with 10 percent extra.
How many cubic yards is a 14x10 patio at 3 inches?
About 1.30 cubic yards.
How much does a cubic yard of crusher run weigh?
Usually around 1.5 to 1.7 compacted tons, depending on stone size, fines and moisture.
How deep should crusher run be for a patio?
The table above shows 3 to 8 inches. Shallower depths suit top dressing; deeper depths suit new installs and heavier use.
How many square feet is 14x10?
140 square feet.
Related guides
- Crushed Stone vs Gravel: Differences and Best Uses
- Tons to Cubic Yards for Gravel: Conversion Chart
- How Many Tons of Gravel in a Dump Truck? Loads and Coverage
- How Much Does a Ton of Gravel Cover? Depth Chart
- How Much Crusher Run for a 12x24 Patio?
- How Much Crusher Run for a 12x30 Patio?
As an Amazon Associate, AsphaltTons.com earns from qualifying purchases. Product links below are sponsored.