How Much Does 10 Tons of Pea Gravel Cover?
How much does 10 tons of pea gravel cover depends on how deep you spread it. At about 1.4 tons per cubic yard, 10 tons is roughly 7.1 cubic yards. Spread 3 inches deep, that covers about 771 square feet. Go thinner and it covers more; go deeper and it covers less.
Volume and tonnage calculator →How the coverage is figured
- Tons to cubic yards: 10 ÷ 1.4 = 7.1 yd³.
- Cubic yards to cubic feet: × 27 = 193 cu ft.
- Divide by depth in feet: at 3 inches (0.250 ft), 193 ÷ 0.250 = 771 sq ft.
Coverage of 10 tons at different depths
| Depth | Square feet covered | Square yards |
|---|---|---|
| 2 in | 1,157 | 129 |
| 3 in | 771 | 86 |
| 4 in | 579 | 64 |
About pea gravel
Pea gravel is small, rounded stone, usually around 3/8 inch. It is comfortable to walk on and drains well, but it shifts under car tires and needs a solid edge to stay put. Weight runs about 1.3 to 1.5 tons per cubic yard, so treat the table as a planning range rather than an exact figure.
Planning around 10 tons
For delivery, 10 tons is in the range of one full tandem load. Ask the supplier how they will split it. Spread from the pile with a loader, skid steer or wheelbarrow, then rake to depth before compacting if the material calls for it.
- Check depth as you go. Stakes marked at the target depth help keep the spread even.
- Expect some loss. Compaction and uneven ground use more than the flat-math figure. Keep about 10 percent in reserve.
- Ask about moisture. Wet material weighs more, so a ton of it covers less.
To run your own numbers, use the volume and tonnage calculator.
Good and poor uses for pea gravel
Good uses:
- Patios, walkways and dog runs
- Play areas with proper depth and edging
- Drainage around foundations when sized properly
Think twice for:
- Driveways and steep paths, where it rolls and ruts
- Under pavers as a base
- Areas without edging
Quick reference numbers
- Per inch over 100 sq ft: about 0.43 tons of pea gravel (0.31 cubic yards).
- Per inch over 1,000 sq ft: about 4.3 tons.
- Another size for comparison: a 10x20 area at 2 inches takes about 1.7 tons.
- Weight used here: about 1.4 tons per cubic yard.
Where estimates go wrong
- Ordering exactly the math. Uneven ground and spillage nearly always need a little more than the flat calculation.
- Mixing up cubic yards and tons. Yards are volume, tons are weight; convert with the product’s weight per yard.
- Ignoring the base. A thin surface layer over soft soil fails early no matter how much material is on top.
- Assuming every supplier uses the same weight. Two yards selling the same product name can quote different tons per yard.
Questions people ask
How many cubic yards is 10 tons of pea gravel?
About 7.1 cubic yards at 1.4 tons per yard.
How many square feet does 10 tons of pea gravel cover at 3 inches?
About 771 square feet.
How many square feet does 10 tons cover at 2 inches?
About 1,157 square feet.
How much does a yard of pea gravel weigh?
About 1.3 to 1.5 tons.
Will 10 tons fit in one truck?
It depends on the truck. Single-axle dump trucks often carry under 10 tons and tandems around 13 to 16; your supplier will know their limits.
Related guides
- How Much Does a Ton of Gravel Cover? Depth Chart
- Tons to Cubic Yards for Gravel: Conversion Chart
- How Many Tons of Gravel in a Dump Truck? Loads and Coverage
- How Much Does 8 Tons of Pea Gravel Cover?
- How Much Does 9 Tons of Pea Gravel Cover?
As an Amazon Associate, AsphaltTons.com earns from qualifying purchases. Product links below are sponsored.