How Much Does 13 Tons of Pea Gravel Cover?
How much does 13 tons of pea gravel cover depends on how deep you spread it. At about 1.4 tons per cubic yard, 13 tons is roughly 9.3 cubic yards. Spread 3 inches deep, that covers about 1,003 square feet. Halve the depth and you roughly double the area.
Volume and tonnage calculator →How the coverage is figured
- Tons to cubic yards: 13 ÷ 1.4 = 9.3 yd³.
- Cubic yards to cubic feet: × 27 = 251 cu ft.
- Divide by depth in feet: at 3 inches (0.250 ft), 251 ÷ 0.250 = 1,003 sq ft.
Coverage of 13 tons at different depths
| Depth | Square feet covered | Square yards |
|---|---|---|
| 2 in | 1,504 | 167 |
| 3 in | 1,003 | 111 |
| 4 in | 752 | 84 |
About pea gravel
Pea gravel is small, rounded stone, usually around 3/8 inch. It is comfortable to walk on and drains well, but it shifts under car tires and needs a solid edge to stay put. Weight runs about 1.3 to 1.5 tons per cubic yard, so treat the table as a planning range rather than an exact figure.
Planning around 13 tons
13 tons is about one tandem-axle truck load, though legal limits vary by truck and state. Spread from the pile with a loader, skid steer or wheelbarrow, then rake to depth before compacting if the material calls for it.
- Check depth as you go. Stakes marked at the target depth help keep the spread even.
- Expect some loss. Compaction and uneven ground use more than the flat-math figure. Keep about 10 percent in reserve.
- Ask about moisture. Wet material weighs more, so a ton of it covers less.
To run your own numbers, use the volume and tonnage calculator.
Where pea gravel fits
Good uses:
- Patios, walkways and dog runs
- Play areas with proper depth and edging
- Drainage around foundations when sized properly
Think twice for:
- Driveways and steep paths, where it rolls and ruts
- Under pavers as a base
- Areas without edging
Quick reference numbers
- Per inch over 100 sq ft: about 0.43 tons of pea gravel (0.31 cubic yards).
- Per inch over 1,000 sq ft: about 4.3 tons.
- Another size for comparison: a 15x30 area at 4 inches takes about 7.8 tons.
- Weight used here: about 1.4 tons per cubic yard.
Mistakes that throw off the order
- Measuring only the main rectangle. Aprons, turnouts and curved edges add real square footage.
- Mixing up cubic yards and tons. Yards are volume, tons are weight; convert with the product’s weight per yard.
- Using inches as if they were feet. Depth has to be divided by 12 before you multiply; skipping that step inflates the order twelvefold.
- Ignoring the base. A thin surface layer over soft soil fails early no matter how much material is on top.
Questions people ask
How many cubic yards is 13 tons of pea gravel?
About 9.3 cubic yards at 1.4 tons per yard.
How many square feet does 13 tons of pea gravel cover at 3 inches?
About 1,003 square feet.
How many square feet does 13 tons cover at 2 inches?
About 1,504 square feet.
How much does a yard of pea gravel weigh?
About 1.3 to 1.5 tons.
Will 13 tons fit in one truck?
It depends on the truck. Single-axle dump trucks often carry under 10 tons and tandems around 13 to 16; your supplier will know their limits.
Related guides
- How Much Does a Ton of Gravel Cover? Depth Chart
- Tons to Cubic Yards for Gravel: Conversion Chart
- How Many Tons of Gravel in a Dump Truck? Loads and Coverage
- How Much Does 11 Tons of Pea Gravel Cover?
- How Much Does 12 Tons of Pea Gravel Cover?
As an Amazon Associate, AsphaltTons.com earns from qualifying purchases. Product links below are sponsored.