How Much Does 14 Tons of Gravel Cover?
How much does 14 tons of gravel cover depends on how deep you spread it. At about 1.4 tons per cubic yard, 14 tons is roughly 10.0 cubic yards. Spread 4 inches deep, that covers about 810 square feet. Go thinner and it covers more; go deeper and it covers less.
Volume and tonnage calculator →How the coverage is figured
- Tons to cubic yards: 14 ÷ 1.4 = 10.0 yd³.
- Cubic yards to cubic feet: × 27 = 270 cu ft.
- Divide by depth in feet: at 4 inches (0.333 ft), 270 ÷ 0.333 = 810 sq ft.
Coverage of 14 tons at different depths
| Depth | Square feet covered | Square yards |
|---|---|---|
| 2 in | 1,620 | 180 |
| 3 in | 1,080 | 120 |
| 4 in | 810 | 90 |
| 6 in | 540 | 60 |
About gravel
Plain gravel is a loose term. Yards use it for rounded bank or river stone as well as for crushed rock, so ask whether the load is washed, crushed or a mix before you lock in a tonnage. Weight runs about 1.3 to 1.5 tons per cubic yard, so treat the table as a planning range rather than an exact figure.
What 14 tons looks like on site
For delivery, 14 tons is in the range of one full tandem load. Ask the supplier how they will split it. Spread from the pile with a loader, skid steer or wheelbarrow, then rake to depth before compacting if the material calls for it.
- Check depth as you go. Stakes marked at the target depth help keep the spread even.
- Expect some loss. Compaction and uneven ground use more than the flat-math figure. Keep about 10 percent in reserve.
- Ask about moisture. Wet material weighs more, so a ton of it covers less.
To run your own numbers, use the volume and tonnage calculator.
When to choose gravel
Works well for:
- Rural driveways and lanes where low upfront cost matters
- Drainage areas and around downspouts
- Temporary access while a site is under construction
Less suited to:
- Steep slopes, where loose stone washes downhill
- Spots plowed often, since plows push gravel into the lawn
- Areas next to doors, because stone tracks inside
Quick reference numbers
- Per inch over 100 sq ft: about 0.43 tons of gravel (0.31 cubic yards).
- Per inch over 1,000 sq ft: about 4.3 tons.
- Another size for comparison: a 8x16 area at 2 inches takes about 1.1 tons.
- Weight used here: about 1.4 tons per cubic yard.
Where estimates go wrong
- Ordering exactly the math. Uneven ground and spillage nearly always need a little more than the flat calculation.
- Mixing up cubic yards and tons. Yards are volume, tons are weight; convert with the product’s weight per yard.
- Using inches as if they were feet. Depth has to be divided by 12 before you multiply; skipping that step inflates the order twelvefold.
- Assuming every supplier uses the same weight. Two yards selling the same product name can quote different tons per yard.
Questions people ask
How many cubic yards is 14 tons of gravel?
About 10.0 cubic yards at 1.4 tons per yard.
How many square feet does 14 tons of gravel cover at 4 inches?
About 810 square feet.
How many square feet does 14 tons cover at 2 inches?
About 1,620 square feet.
How much does a yard of gravel weigh?
About 1.3 to 1.5 tons.
Will 14 tons fit in one truck?
It depends on the truck. Single-axle dump trucks often carry under 10 tons and tandems around 13 to 16; your supplier will know their limits.
Related guides
- How Much Does a Ton of Gravel Cover? Depth Chart
- Tons to Cubic Yards for Gravel: Conversion Chart
- How Many Tons of Gravel in a Dump Truck? Loads and Coverage
- How Much Does 12 Tons of Gravel Cover?
- How Much Does 13 Tons of Gravel Cover?
As an Amazon Associate, AsphaltTons.com earns from qualifying purchases. Product links below are sponsored.