How Much Does 2 Tons of Road Base Cover?
How much does 2 tons of road base cover depends on how deep you spread it. At about 1.5 tons per cubic yard, 2 tons is roughly 1.3 cubic yards. Spread 6 inches deep, that covers about 72 square feet. Halve the depth and you roughly double the area.
Volume and tonnage calculator →How the coverage is figured
- Tons to cubic yards: 2 ÷ 1.5 = 1.3 yd³.
- Cubic yards to cubic feet: × 27 = 36 cu ft.
- Divide by depth in feet: at 6 inches (0.500 ft), 36 ÷ 0.500 = 72 sq ft.
Coverage of 2 tons at different depths
| Depth | Square feet covered | Square yards |
|---|---|---|
| 4 in | 108 | 12 |
| 6 in | 72 | 8 |
| 8 in | 54 | 6 |
About road base
Road base is meant to be compacted at close to the right moisture. Dry base rock does not lock up well; a light spray of water before rolling helps. Weight runs about 1.4 to 1.65 compacted tons per cubic yard, so treat the table as a planning range rather than an exact figure.
Planning around 2 tons
2 tons is a light load that a single-axle dump truck can often handle, though legal limits vary by truck and state. Spread from the pile with a loader, skid steer or wheelbarrow, then rake to depth before compacting if the material calls for it.
- Check depth as you go. Stakes marked at the target depth help keep the spread even.
- Expect some loss. Compaction and uneven ground use more than the flat-math figure. Keep about 10 percent in reserve.
- Ask about moisture. Wet material weighs more, so a ton of it covers less.
To run your own numbers, use the volume and tonnage calculator.
When to choose road base
Works well for:
- Base under asphalt and concrete
- Gravel roads and drives
- Equipment and shed pads
Think twice for:
- Drainage layers
- Decorative surfaces
- Surfaces that will stay uncompacted
Quick reference numbers
- Per inch over 100 sq ft: about 0.46 tons of road base (0.31 cubic yards).
- Per inch over 1,000 sq ft: about 4.6 tons.
- Another size for comparison: a 20x25 area at 2 inches takes about 4.6 tons.
- Weight used here: about 1.5 tons per cubic yard.
Mistakes that throw off the order
- Skipping drainage. Water sitting under any surface softens the base and leads to ruts and potholes.
- Measuring only the main rectangle. Aprons, turnouts and curved edges add real square footage.
- Using inches as if they were feet. Depth has to be divided by 12 before you multiply; skipping that step inflates the order twelvefold.
- Ordering exactly the math. Uneven ground and spillage nearly always need a little more than the flat calculation.
Questions people ask
How many cubic yards is 2 tons of road base?
About 1.3 cubic yards at 1.5 tons per yard.
How many square feet does 2 tons of road base cover at 6 inches?
About 72 square feet.
How many square feet does 2 tons cover at 4 inches?
About 108 square feet.
How much does a yard of road base weigh?
About 1.4 to 1.65 compacted tons.
Will 2 tons fit in one truck?
It depends on the truck. Single-axle dump trucks often carry under 10 tons and tandems around 13 to 16; your supplier will know their limits.
Related guides
- Crushed Stone vs Gravel: Differences and Best Uses
- Tons to Cubic Yards for Gravel: Conversion Chart
- How Many Tons of Gravel in a Dump Truck? Loads and Coverage
As an Amazon Associate, AsphaltTons.com earns from qualifying purchases. Product links below are sponsored.