How Much Does 2 Tons of Recycled Concrete Aggregate Cover?
How much does 2 tons of recycled concrete aggregate cover depends on how deep you spread it. At about 1.3 tons per cubic yard, 2 tons is roughly 1.5 cubic yards. Spread 4 inches deep, that covers about 125 square feet. Halve the depth and you roughly double the area.
Volume and tonnage calculator →How the coverage is figured
- Tons to cubic yards: 2 ÷ 1.3 = 1.5 yd³.
- Cubic yards to cubic feet: × 27 = 42 cu ft.
- Divide by depth in feet: at 4 inches (0.333 ft), 42 ÷ 0.333 = 125 sq ft.
Coverage of 2 tons at different depths
| Depth | Square feet covered | Square yards |
|---|---|---|
| 3 in | 166 | 18 |
| 4 in | 125 | 14 |
| 6 in | 83 | 9 |
About recycled concrete aggregate
Ask whether the recycled concrete has been screened for rebar and debris. Fresh-crushed concrete can also be alkaline, so keep it away from sensitive plantings and streams. Weight runs about 1.2 to 1.4 tons per cubic yard, so treat the table as a planning range rather than an exact figure.
Planning around 2 tons
For delivery, 2 tons usually fits on one smaller dump truck. Ask the supplier how they will split it. Spread from the pile with a loader, skid steer or wheelbarrow, then rake to depth before compacting if the material calls for it.
- Check depth as you go. Stakes marked at the target depth help keep the spread even.
- Expect some loss. Compaction and uneven ground use more than the flat-math figure. Keep about 10 percent in reserve.
- Ask about moisture. Wet material weighs more, so a ton of it covers less.
To run your own numbers, use the volume and tonnage calculator.
When to choose recycled concrete aggregate
Works well for:
- Driveway and pad bases
- Temporary construction entrances
- Fill under slabs when compacted in lifts
Less suited to:
- Near ponds, streams or sensitive plants, since fresh crush can raise pH
- Decorative top layers
- Drainage layers, unless the product is clean and screened
Quick reference numbers
- Per inch over 100 sq ft: about 0.40 tons of recycled concrete aggregate (0.31 cubic yards).
- Per inch over 1,000 sq ft: about 4.0 tons.
- Another size for comparison: a 10x20 area at 3 inches takes about 2.4 tons.
- Weight used here: about 1.3 tons per cubic yard.
Common estimating mistakes
- Skipping drainage. Water sitting under any surface softens the base and leads to ruts and potholes.
- Ordering exactly the math. Uneven ground and spillage nearly always need a little more than the flat calculation.
- Forgetting that compaction shrinks loose material. A loose 4-inch spread of a dense-graded stone may finish closer to 3 inches after rolling.
- Measuring only the main rectangle. Aprons, turnouts and curved edges add real square footage.
Questions people ask
How many cubic yards is 2 tons of recycled concrete aggregate?
About 1.5 cubic yards at 1.3 tons per yard.
How many square feet does 2 tons of recycled concrete aggregate cover at 4 inches?
About 125 square feet.
How many square feet does 2 tons cover at 3 inches?
About 166 square feet.
How much does a yard of recycled concrete aggregate weigh?
About 1.2 to 1.4 tons.
Will 2 tons fit in one truck?
It depends on the truck. Single-axle dump trucks often carry under 10 tons and tandems around 13 to 16; your supplier will know their limits.
Related guides
- Crushed Stone vs Gravel: Differences and Best Uses
- Tons to Cubic Yards for Gravel: Conversion Chart
- How Many Tons of Gravel in a Dump Truck? Loads and Coverage
As an Amazon Associate, AsphaltTons.com earns from qualifying purchases. Product links below are sponsored.