How Much Does 22 Tons of River Rock Cover?
How much does 22 tons of river rock cover depends on how deep you spread it. At about 1.35 tons per cubic yard, 22 tons is roughly 16.3 cubic yards. Spread 3 inches deep, that covers about 1,760 square feet. Every added inch of depth cuts the coverage noticeably.
Volume and tonnage calculator →How the coverage is figured
- Tons to cubic yards: 22 ÷ 1.35 = 16.3 yd³.
- Cubic yards to cubic feet: × 27 = 440 cu ft.
- Divide by depth in feet: at 3 inches (0.250 ft), 440 ÷ 0.250 = 1,760 sq ft.
Coverage of 22 tons at different depths
| Depth | Square feet covered | Square yards |
|---|---|---|
| 2 in | 2,640 | 293 |
| 3 in | 1,760 | 196 |
| 4 in | 1,320 | 147 |
About river rock
River rock is smooth, water-worn stone sold in sizes from about 3/4 inch to several inches. Larger sizes cover fewer square feet per ton at the same depth because the voids between stones are bigger. Weight runs about 1.25 to 1.45 tons per cubic yard, so treat the table as a planning range rather than an exact figure.
Planning around 22 tons
22 tons will usually take two or more truck loads, though legal limits vary by truck and state. Spread from the pile with a loader, skid steer or wheelbarrow, then rake to depth before compacting if the material calls for it.
- Check depth as you go. Stakes marked at the target depth help keep the spread even.
- Expect some loss. Compaction and uneven ground use more than the flat-math figure. Keep about 10 percent in reserve.
- Ask about moisture. Wet material weighs more, so a ton of it covers less.
To run your own numbers, use the volume and tonnage calculator.
When to choose river rock
Works well for:
- Dry creek beds and drainage swales
- Decorative borders and planting beds
- Around downspouts to stop splash erosion
Poor fit for:
- Walking surfaces
- Driveways
- Bases under slabs or pavers
Quick reference numbers
- Per inch over 100 sq ft: about 0.42 tons of river rock (0.31 cubic yards).
- Per inch over 1,000 sq ft: about 4.2 tons.
- Another size for comparison: a 20x25 area at 2 inches takes about 4.2 tons.
- Weight used here: about 1.35 tons per cubic yard.
Mistakes that throw off the order
- Skipping drainage. Water sitting under any surface softens the base and leads to ruts and potholes.
- Ignoring the base. A thin surface layer over soft soil fails early no matter how much material is on top.
- Using inches as if they were feet. Depth has to be divided by 12 before you multiply; skipping that step inflates the order twelvefold.
- Forgetting that compaction shrinks loose material. A loose 4-inch spread of a dense-graded stone may finish closer to 3 inches after rolling.
Questions people ask
How many cubic yards is 22 tons of river rock?
About 16.3 cubic yards at 1.35 tons per yard.
How many square feet does 22 tons of river rock cover at 3 inches?
About 1,760 square feet.
How many square feet does 22 tons cover at 2 inches?
About 2,640 square feet.
How much does a yard of river rock weigh?
About 1.25 to 1.45 tons.
Will 22 tons fit in one truck?
It depends on the truck. Single-axle dump trucks often carry under 10 tons and tandems around 13 to 16; your supplier will know their limits.
Related guides
- How Much Does a Ton of River Rock Cover?
- Tons to Cubic Yards for Gravel: Conversion Chart
- How Many Tons of Gravel in a Dump Truck? Loads and Coverage
- How Much Does 20 Tons of River Rock Cover?
- How Much Does 21 Tons of River Rock Cover?
As an Amazon Associate, AsphaltTons.com earns from qualifying purchases. Product links below are sponsored.