How Much Does 23 Tons of Sand Cover?
How much does 23 tons of sand cover depends on how deep you spread it. At about 1.35 tons per cubic yard, 23 tons is roughly 17.0 cubic yards. Spread 3 inches deep, that covers about 1,840 square feet. Halve the depth and you roughly double the area.
Volume and tonnage calculator →How the coverage is figured
- Tons to cubic yards: 23 ÷ 1.35 = 17.0 yd³.
- Cubic yards to cubic feet: × 27 = 460 cu ft.
- Divide by depth in feet: at 3 inches (0.250 ft), 460 ÷ 0.250 = 1,840 sq ft.
Coverage of 23 tons at different depths
| Depth | Square feet covered | Square yards |
|---|---|---|
| 1 in | 5,520 | 613 |
| 2 in | 2,760 | 307 |
| 3 in | 1,840 | 204 |
| 4 in | 1,380 | 153 |
About sand
For paver bedding, concrete sand (coarse, washed) is the usual pick. Mason sand is finer and used in mortar and play areas. Weight runs about 1.3 to 1.5 dry tons per cubic yard, so treat the table as a planning range rather than an exact figure.
Putting 23 tons to use
For delivery, 23 tons means multiple trips or a larger truck. Ask the supplier how they will split it. Spread from the pile with a loader, skid steer or wheelbarrow, then rake to depth before compacting if the material calls for it.
- Check depth as you go. Stakes marked at the target depth help keep the spread even.
- Expect some loss. Compaction and uneven ground use more than the flat-math figure. Keep about 10 percent in reserve.
- Ask about moisture. Wet material weighs more, so a ton of it covers less.
To run your own numbers, use the volume and tonnage calculator.
When to choose sand
Best suited to:
- Paver and flagstone bedding
- Leveling under above-ground pools (with the right product)
- Filling joints and backfilling pipe
Less suited to:
- Driveway bases, since sand shifts under load
- Steep areas exposed to runoff
- Thick layers under pavers, which settle unevenly
Quick reference numbers
- Per inch over 100 sq ft: about 0.42 tons of sand (0.31 cubic yards).
- Per inch over 1,000 sq ft: about 4.2 tons.
- Another size for comparison: a 14x28 area at 2 inches takes about 3.3 tons.
- Weight used here: about 1.35 tons per cubic yard.
Common estimating mistakes
- Mixing up cubic yards and tons. Yards are volume, tons are weight; convert with the product’s weight per yard.
- Skipping drainage. Water sitting under any surface softens the base and leads to ruts and potholes.
- Ordering exactly the math. Uneven ground and spillage nearly always need a little more than the flat calculation.
- Assuming every supplier uses the same weight. Two yards selling the same product name can quote different tons per yard.
Questions people ask
How many cubic yards is 23 tons of sand?
About 17.0 cubic yards at 1.35 tons per yard.
How many square feet does 23 tons of sand cover at 3 inches?
About 1,840 square feet.
How many square feet does 23 tons cover at 1 inches?
About 5,520 square feet.
How much does a yard of sand weigh?
About 1.3 to 1.5 dry tons.
Will 23 tons fit in one truck?
It depends on the truck. Single-axle dump trucks often carry under 10 tons and tandems around 13 to 16; your supplier will know their limits.
Related guides
- How Much Does a Ton of Sand Cover?
- Tons to Cubic Yards for Gravel: Conversion Chart
- How Many Tons of Gravel in a Dump Truck? Loads and Coverage
- How Much Does 21 Tons of Sand Cover?
- How Much Does 22 Tons of Sand Cover?
As an Amazon Associate, AsphaltTons.com earns from qualifying purchases. Product links below are sponsored.