How Much Does 26 Tons of Asphalt Millings Cover?
How much does 26 tons of asphalt millings cover depends on how deep you spread it. At about 1.3 tons per cubic yard, 26 tons is roughly 20.0 cubic yards. Spread 4 inches deep, that covers about 1,620 square feet. Every added inch of depth cuts the coverage noticeably.
Volume and tonnage calculator →How the coverage is figured
- Tons to cubic yards: 26 ÷ 1.3 = 20.0 yd³.
- Cubic yards to cubic feet: × 27 = 540 cu ft.
- Divide by depth in feet: at 4 inches (0.333 ft), 540 ÷ 0.333 = 1,620 sq ft.
Coverage of 26 tons at different depths
| Depth | Square feet covered | Square yards |
|---|---|---|
| 3 in | 2,160 | 240 |
| 4 in | 1,620 | 180 |
| 6 in | 1,080 | 120 |
About asphalt millings
Asphalt millings are ground-up old pavement. When compacted and warmed by sun they bind into a fairly firm surface, which is why they are popular for rural drives and lots. Weight runs about 1.2 to 1.4 loose tons per cubic yard, so treat the table as a planning range rather than an exact figure.
Planning around 26 tons
26 tons will usually take two or more truck loads, though legal limits vary by truck and state. Spread from the pile with a loader, skid steer or wheelbarrow, then rake to depth before compacting if the material calls for it.
- Check depth as you go. Stakes marked at the target depth help keep the spread even.
- Expect some loss. Compaction and uneven ground use more than the flat-math figure. Keep about 10 percent in reserve.
- Ask about moisture. Wet material weighs more, so a ton of it covers less.
To run your own numbers, use the volume and tonnage calculator.
When to choose asphalt millings
Best suited to:
- Rural driveways and farm lanes
- Parking areas where a dust-free surface is wanted
- Low-cost base under a future paved surface
Less suited to:
- Areas near wells or streams where local rules limit them
- Decorative or barefoot areas
- Jobs needing a uniform, clean look
Quick reference numbers
- Per inch over 100 sq ft: about 0.40 tons of asphalt millings (0.31 cubic yards).
- Per inch over 1,000 sq ft: about 4.0 tons.
- Another size for comparison: a 15x30 area at 2 inches takes about 3.6 tons.
- Weight used here: about 1.3 tons per cubic yard.
Common estimating mistakes
- Assuming every supplier uses the same weight. Two yards selling the same product name can quote different tons per yard.
- Ignoring the base. A thin surface layer over soft soil fails early no matter how much material is on top.
- Forgetting that compaction shrinks loose material. A loose 4-inch spread of a dense-graded stone may finish closer to 3 inches after rolling.
- Measuring only the main rectangle. Aprons, turnouts and curved edges add real square footage.
Questions people ask
How many cubic yards is 26 tons of asphalt millings?
About 20.0 cubic yards at 1.3 tons per yard.
How many square feet does 26 tons of asphalt millings cover at 4 inches?
About 1,620 square feet.
How many square feet does 26 tons cover at 3 inches?
About 2,160 square feet.
How much does a yard of asphalt millings weigh?
About 1.2 to 1.4 loose tons.
Will 26 tons fit in one truck?
It depends on the truck. Single-axle dump trucks often carry under 10 tons and tandems around 13 to 16; your supplier will know their limits.
Related guides
- How Many Tons of Asphalt Millings for a 40x25 Area?
- Tons to Cubic Yards for Gravel: Conversion Chart
- How Many Tons of Gravel in a Dump Truck? Loads and Coverage
- How Much Does 24 Tons of Asphalt Millings Cover?
- How Much Does 25 Tons of Asphalt Millings Cover?
As an Amazon Associate, AsphaltTons.com earns from qualifying purchases. Product links below are sponsored.