How Much Does 27 Tons of Crushed Stone Cover?
How much does 27 tons of crushed stone cover depends on how deep you spread it. At about 1.4 tons per cubic yard, 27 tons is roughly 19.3 cubic yards. Spread 4 inches deep, that covers about 1,562 square feet. Go thinner and it covers more; go deeper and it covers less.
Volume and tonnage calculator →How the coverage is figured
- Tons to cubic yards: 27 ÷ 1.4 = 19.3 yd³.
- Cubic yards to cubic feet: × 27 = 521 cu ft.
- Divide by depth in feet: at 4 inches (0.333 ft), 521 ÷ 0.333 = 1,562 sq ft.
Coverage of 27 tons at different depths
| Depth | Square feet covered | Square yards |
|---|---|---|
| 2 in | 3,124 | 347 |
| 3 in | 2,083 | 231 |
| 4 in | 1,562 | 174 |
| 6 in | 1,041 | 116 |
About crushed stone
Most quarries sell crushed stone by a size number or a screen size. Clean crushed stone drains well; stone with fines packs harder but sheds water more slowly. Weight runs about 1.35 to 1.5 tons per cubic yard, so treat the table as a planning range rather than an exact figure.
Planning around 27 tons
For delivery, 27 tons means multiple trips or a larger truck. Ask the supplier how they will split it. Spread from the pile with a loader, skid steer or wheelbarrow, then rake to depth before compacting if the material calls for it.
- Check depth as you go. Stakes marked at the target depth help keep the spread even.
- Expect some loss. Compaction and uneven ground use more than the flat-math figure. Keep about 10 percent in reserve.
- Ask about moisture. Wet material weighs more, so a ton of it covers less.
To run your own numbers, use the volume and tonnage calculator.
When to choose crushed stone
Best suited to:
- Driveway top courses and parking pads
- Shed and hot tub bases
- Backfill behind walls when a clean size is used
Less suited to:
- Barefoot areas, since angular stone is rough
- Play areas
- Places that need a smooth rolling surface for wheels
Quick reference numbers
- Per inch over 100 sq ft: about 0.43 tons of crushed stone (0.31 cubic yards).
- Per inch over 1,000 sq ft: about 4.3 tons.
- Another size for comparison: a 10x20 area at 4 inches takes about 3.5 tons.
- Weight used here: about 1.4 tons per cubic yard.
Mistakes that throw off the order
- Mixing up cubic yards and tons. Yards are volume, tons are weight; convert with the product’s weight per yard.
- Using inches as if they were feet. Depth has to be divided by 12 before you multiply; skipping that step inflates the order twelvefold.
- Skipping drainage. Water sitting under any surface softens the base and leads to ruts and potholes.
- Ignoring the base. A thin surface layer over soft soil fails early no matter how much material is on top.
Questions people ask
How many cubic yards is 27 tons of crushed stone?
About 19.3 cubic yards at 1.4 tons per yard.
How many square feet does 27 tons of crushed stone cover at 4 inches?
About 1,562 square feet.
How many square feet does 27 tons cover at 2 inches?
About 3,124 square feet.
How much does a yard of crushed stone weigh?
About 1.35 to 1.5 tons.
Will 27 tons fit in one truck?
It depends on the truck. Single-axle dump trucks often carry under 10 tons and tandems around 13 to 16; your supplier will know their limits.
Related guides
- How Much Does a Ton of Crushed Stone Cover?
- Tons to Cubic Yards for Gravel: Conversion Chart
- How Many Tons of Gravel in a Dump Truck? Loads and Coverage
- How Much Does 25 Tons of Crushed Stone Cover?
- How Much Does 26 Tons of Crushed Stone Cover?
As an Amazon Associate, AsphaltTons.com earns from qualifying purchases. Product links below are sponsored.