How Much Does 27 Tons of River Rock Cover?
How much does 27 tons of river rock cover depends on how deep you spread it. At about 1.35 tons per cubic yard, 27 tons is roughly 20.0 cubic yards. Spread 3 inches deep, that covers about 2,160 square feet. Every added inch of depth cuts the coverage noticeably.
Volume and tonnage calculator →How the coverage is figured
- Tons to cubic yards: 27 ÷ 1.35 = 20.0 yd³.
- Cubic yards to cubic feet: × 27 = 540 cu ft.
- Divide by depth in feet: at 3 inches (0.250 ft), 540 ÷ 0.250 = 2,160 sq ft.
Coverage of 27 tons at different depths
| Depth | Square feet covered | Square yards |
|---|---|---|
| 2 in | 3,240 | 360 |
| 3 in | 2,160 | 240 |
| 4 in | 1,620 | 180 |
About river rock
River rock is smooth, water-worn stone sold in sizes from about 3/4 inch to several inches. Larger sizes cover fewer square feet per ton at the same depth because the voids between stones are bigger. Weight runs about 1.25 to 1.45 tons per cubic yard, so treat the table as a planning range rather than an exact figure.
Planning around 27 tons
27 tons will usually take two or more truck loads, though legal limits vary by truck and state. Spread from the pile with a loader, skid steer or wheelbarrow, then rake to depth before compacting if the material calls for it.
- Check depth as you go. Stakes marked at the target depth help keep the spread even.
- Expect some loss. Compaction and uneven ground use more than the flat-math figure. Keep about 10 percent in reserve.
- Ask about moisture. Wet material weighs more, so a ton of it covers less.
To run your own numbers, use the volume and tonnage calculator.
Where river rock fits
Works well for:
- Dry creek beds and drainage swales
- Decorative borders and planting beds
- Around downspouts to stop splash erosion
Think twice for:
- Walking surfaces
- Driveways
- Bases under slabs or pavers
Quick reference numbers
- Per inch over 100 sq ft: about 0.42 tons of river rock (0.31 cubic yards).
- Per inch over 1,000 sq ft: about 4.2 tons.
- Another size for comparison: a 12x24 area at 2 inches takes about 2.4 tons.
- Weight used here: about 1.35 tons per cubic yard.
Common estimating mistakes
- Assuming every supplier uses the same weight. Two yards selling the same product name can quote different tons per yard.
- Forgetting that compaction shrinks loose material. A loose 4-inch spread of a dense-graded stone may finish closer to 3 inches after rolling.
- Using inches as if they were feet. Depth has to be divided by 12 before you multiply; skipping that step inflates the order twelvefold.
- Ordering exactly the math. Uneven ground and spillage nearly always need a little more than the flat calculation.
Questions people ask
How many cubic yards is 27 tons of river rock?
About 20.0 cubic yards at 1.35 tons per yard.
How many square feet does 27 tons of river rock cover at 3 inches?
About 2,160 square feet.
How many square feet does 27 tons cover at 2 inches?
About 3,240 square feet.
How much does a yard of river rock weigh?
About 1.25 to 1.45 tons.
Will 27 tons fit in one truck?
It depends on the truck. Single-axle dump trucks often carry under 10 tons and tandems around 13 to 16; your supplier will know their limits.
Related guides
- How Much Does a Ton of River Rock Cover?
- Tons to Cubic Yards for Gravel: Conversion Chart
- How Many Tons of Gravel in a Dump Truck? Loads and Coverage
- How Much Does 25 Tons of River Rock Cover?
- How Much Does 26 Tons of River Rock Cover?
As an Amazon Associate, AsphaltTons.com earns from qualifying purchases. Product links below are sponsored.