How Much Does 35 Tons of Crusher Run Cover?
How much does 35 tons of crusher run cover depends on how deep you spread it. At about 1.55 tons per cubic yard, 35 tons is roughly 22.6 cubic yards. Spread 6 inches deep, that covers about 1,219 square feet. Halve the depth and you roughly double the area.
Volume and tonnage calculator →How the coverage is figured
- Tons to cubic yards: 35 ÷ 1.55 = 22.6 yd³.
- Cubic yards to cubic feet: × 27 = 610 cu ft.
- Divide by depth in feet: at 6 inches (0.500 ft), 610 ÷ 0.500 = 1,219 sq ft.
Coverage of 35 tons at different depths
| Depth | Square feet covered | Square yards |
|---|---|---|
| 3 in | 2,439 | 271 |
| 4 in | 1,829 | 203 |
| 6 in | 1,219 | 135 |
| 8 in | 915 | 102 |
About crusher run
The fines in crusher run fill the gaps between stones, so it weighs more per yard than clean stone once compacted. Plan on rolling or plate-compacting it in lifts. Weight runs about 1.5 to 1.7 compacted tons per cubic yard, so treat the table as a planning range rather than an exact figure.
Planning around 35 tons
35 tons will usually take two or more truck loads, though legal limits vary by truck and state. Spread from the pile with a loader, skid steer or wheelbarrow, then rake to depth before compacting if the material calls for it.
- Check depth as you go. Stakes marked at the target depth help keep the spread even.
- Expect some loss. Compaction and uneven ground use more than the flat-math figure. Keep about 10 percent in reserve.
- Ask about moisture. Wet material weighs more, so a ton of it covers less.
To run your own numbers, use the volume and tonnage calculator.
Where crusher run fits
Good uses:
- Base under asphalt, pavers or concrete
- Gravel drives that need a firm, packed surface
- Shed pads and equipment pads
Think twice for:
- Drainage layers, since the fines slow water
- Decorative beds
- Spots where you want water to soak straight through
Quick reference numbers
- Per inch over 100 sq ft: about 0.48 tons of crusher run (0.31 cubic yards).
- Per inch over 1,000 sq ft: about 4.8 tons.
- Another size for comparison: a 12x24 area at 4 inches takes about 5.5 tons.
- Weight used here: about 1.55 tons per cubic yard.
Common estimating mistakes
- Measuring only the main rectangle. Aprons, turnouts and curved edges add real square footage.
- Ordering exactly the math. Uneven ground and spillage nearly always need a little more than the flat calculation.
- Using inches as if they were feet. Depth has to be divided by 12 before you multiply; skipping that step inflates the order twelvefold.
- Assuming every supplier uses the same weight. Two yards selling the same product name can quote different tons per yard.
Questions people ask
How many cubic yards is 35 tons of crusher run?
About 22.6 cubic yards at 1.55 tons per yard.
How many square feet does 35 tons of crusher run cover at 6 inches?
About 1,219 square feet.
How many square feet does 35 tons cover at 3 inches?
About 2,439 square feet.
How much does a yard of crusher run weigh?
About 1.5 to 1.7 compacted tons.
Will 35 tons fit in one truck?
It depends on the truck. Single-axle dump trucks often carry under 10 tons and tandems around 13 to 16; your supplier will know their limits.
Related guides
- Crushed Stone vs Gravel: Differences and Best Uses
- Tons to Cubic Yards for Gravel: Conversion Chart
- How Many Tons of Gravel in a Dump Truck? Loads and Coverage
- How Much Does 29 Tons of Crusher Run Cover?
- How Much Does 30 Tons of Crusher Run Cover?
As an Amazon Associate, AsphaltTons.com earns from qualifying purchases. Product links below are sponsored.