How Much Does 4 Tons of Limestone Screenings Cover?
How much does 4 tons of limestone screenings cover depends on how deep you spread it. At about 1.4 tons per cubic yard, 4 tons is roughly 2.9 cubic yards. Spread 2 inches deep, that covers about 463 square feet. Go thinner and it covers more; go deeper and it covers less.
Volume and tonnage calculator →How the coverage is figured
- Tons to cubic yards: 4 ÷ 1.4 = 2.9 yd³.
- Cubic yards to cubic feet: × 27 = 77 cu ft.
- Divide by depth in feet: at 2 inches (0.167 ft), 77 ÷ 0.167 = 463 sq ft.
Coverage of 4 tons at different depths
| Depth | Square feet covered | Square yards |
|---|---|---|
| 1 in | 926 | 103 |
| 2 in | 463 | 51 |
| 3 in | 309 | 34 |
About limestone screenings
Screenings hold moisture and can crust over. Use them in thin layers over a compacted stone base instead of as a thick layer on their own. Weight runs about 1.3 to 1.5 tons per cubic yard, so treat the table as a planning range rather than an exact figure.
Planning around 4 tons
For delivery, 4 tons usually fits on one smaller dump truck. Ask the supplier how they will split it. Spread from the pile with a loader, skid steer or wheelbarrow, then rake to depth before compacting if the material calls for it.
- Check depth as you go. Stakes marked at the target depth help keep the spread even.
- Expect some loss. Compaction and uneven ground use more than the flat-math figure. Keep about 10 percent in reserve.
- Ask about moisture. Wet material weighs more, so a ton of it covers less.
To run your own numbers, use the volume and tonnage calculator.
Where limestone screenings fits
Works well for:
- Paver and flagstone setting beds
- Firm walking paths
- Top-dressing a compacted stone base
Poor fit for:
- Deep layers on their own
- Low spots that collect water
- Under heavy vehicle traffic without a base
Quick reference numbers
- Per inch over 100 sq ft: about 0.43 tons of limestone screenings (0.31 cubic yards).
- Per inch over 1,000 sq ft: about 4.3 tons.
- Another size for comparison: a 20x25 area at 3 inches takes about 6.5 tons.
- Weight used here: about 1.4 tons per cubic yard.
Where estimates go wrong
- Forgetting that compaction shrinks loose material. A loose 4-inch spread of a dense-graded stone may finish closer to 3 inches after rolling.
- Ordering exactly the math. Uneven ground and spillage nearly always need a little more than the flat calculation.
- Mixing up cubic yards and tons. Yards are volume, tons are weight; convert with the product’s weight per yard.
- Assuming every supplier uses the same weight. Two yards selling the same product name can quote different tons per yard.
Questions people ask
How many cubic yards is 4 tons of limestone screenings?
About 2.9 cubic yards at 1.4 tons per yard.
How many square feet does 4 tons of limestone screenings cover at 2 inches?
About 463 square feet.
How many square feet does 4 tons cover at 1 inches?
About 926 square feet.
How much does a yard of limestone screenings weigh?
About 1.3 to 1.5 tons.
Will 4 tons fit in one truck?
It depends on the truck. Single-axle dump trucks often carry under 10 tons and tandems around 13 to 16; your supplier will know their limits.
Related guides
- #10 Stone (Stone Dust): Size, Uses and How Many Tons
- Tons to Cubic Yards for Gravel: Conversion Chart
- How Many Tons of Gravel in a Dump Truck? Loads and Coverage
- How Much Does 2 Tons of Limestone Screenings Cover?
- How Much Does 3 Tons of Limestone Screenings Cover?
As an Amazon Associate, AsphaltTons.com earns from qualifying purchases. Product links below are sponsored.