How Much Does 45 Tons of Gravel Cover?
How much does 45 tons of gravel cover depends on how deep you spread it. At about 1.4 tons per cubic yard, 45 tons is roughly 32.1 cubic yards. Spread 4 inches deep, that covers about 2,604 square feet. Go thinner and it covers more; go deeper and it covers less.
Volume and tonnage calculator →How the coverage is figured
- Tons to cubic yards: 45 ÷ 1.4 = 32.1 yd³.
- Cubic yards to cubic feet: × 27 = 868 cu ft.
- Divide by depth in feet: at 4 inches (0.333 ft), 868 ÷ 0.333 = 2,604 sq ft.
Coverage of 45 tons at different depths
| Depth | Square feet covered | Square yards |
|---|---|---|
| 2 in | 5,207 | 579 |
| 3 in | 3,471 | 386 |
| 4 in | 2,604 | 289 |
| 6 in | 1,736 | 193 |
About gravel
Because ’gravel’ covers so many products, the weight per yard moves with stone size and how much fine material is in the pile. Rounded stone with no fines rolls under tires; crushed stone with fines locks together. Weight runs about 1.3 to 1.5 tons per cubic yard, so treat the table as a planning range rather than an exact figure.
Planning around 45 tons
45 tons will usually take two or more truck loads, though legal limits vary by truck and state. Spread from the pile with a loader, skid steer or wheelbarrow, then rake to depth before compacting if the material calls for it.
- Check depth as you go. Stakes marked at the target depth help keep the spread even.
- Expect some loss. Compaction and uneven ground use more than the flat-math figure. Keep about 10 percent in reserve.
- Ask about moisture. Wet material weighs more, so a ton of it covers less.
To run your own numbers, use the volume and tonnage calculator.
Good and poor uses for gravel
Good uses:
- Rural driveways and lanes where low upfront cost matters
- Drainage areas and around downspouts
- Temporary access while a site is under construction
Less suited to:
- Steep slopes, where loose stone washes downhill
- Spots plowed often, since plows push gravel into the lawn
- Areas next to doors, because stone tracks inside
Quick reference numbers
- Per inch over 100 sq ft: about 0.43 tons of gravel (0.31 cubic yards).
- Per inch over 1,000 sq ft: about 4.3 tons.
- Another size for comparison: a 12x24 area at 4 inches takes about 5.0 tons.
- Weight used here: about 1.4 tons per cubic yard.
Mistakes that throw off the order
- Measuring only the main rectangle. Aprons, turnouts and curved edges add real square footage.
- Skipping drainage. Water sitting under any surface softens the base and leads to ruts and potholes.
- Ordering exactly the math. Uneven ground and spillage nearly always need a little more than the flat calculation.
- Using inches as if they were feet. Depth has to be divided by 12 before you multiply; skipping that step inflates the order twelvefold.
Questions people ask
How many cubic yards is 45 tons of gravel?
About 32.1 cubic yards at 1.4 tons per yard.
How many square feet does 45 tons of gravel cover at 4 inches?
About 2,604 square feet.
How many square feet does 45 tons cover at 2 inches?
About 5,207 square feet.
How much does a yard of gravel weigh?
About 1.3 to 1.5 tons.
Will 45 tons fit in one truck?
It depends on the truck. Single-axle dump trucks often carry under 10 tons and tandems around 13 to 16; your supplier will know their limits.
Related guides
- How Much Does a Ton of Gravel Cover? Depth Chart
- Tons to Cubic Yards for Gravel: Conversion Chart
- How Many Tons of Gravel in a Dump Truck? Loads and Coverage
- How Much Does 35 Tons of Gravel Cover?
- How Much Does 40 Tons of Gravel Cover?
As an Amazon Associate, AsphaltTons.com earns from qualifying purchases. Product links below are sponsored.