How Much Does 6 Tons of Pea Gravel Cover?
How much does 6 tons of pea gravel cover depends on how deep you spread it. At about 1.4 tons per cubic yard, 6 tons is roughly 4.3 cubic yards. Spread 3 inches deep, that covers about 463 square feet. Every added inch of depth cuts the coverage noticeably.
Volume and tonnage calculator →How the coverage is figured
- Tons to cubic yards: 6 ÷ 1.4 = 4.3 yd³.
- Cubic yards to cubic feet: × 27 = 116 cu ft.
- Divide by depth in feet: at 3 inches (0.250 ft), 116 ÷ 0.250 = 463 sq ft.
Coverage of 6 tons at different depths
| Depth | Square feet covered | Square yards |
|---|---|---|
| 2 in | 694 | 77 |
| 3 in | 463 | 51 |
| 4 in | 347 | 39 |
About pea gravel
Pea gravel is small, rounded stone, usually around 3/8 inch. It is comfortable to walk on and drains well, but it shifts under car tires and needs a solid edge to stay put. Weight runs about 1.3 to 1.5 tons per cubic yard, so treat the table as a planning range rather than an exact figure.
What 6 tons looks like on site
6 tons is a light load that a single-axle dump truck can often handle, though legal limits vary by truck and state. Spread from the pile with a loader, skid steer or wheelbarrow, then rake to depth before compacting if the material calls for it.
- Check depth as you go. Stakes marked at the target depth help keep the spread even.
- Expect some loss. Compaction and uneven ground use more than the flat-math figure. Keep about 10 percent in reserve.
- Ask about moisture. Wet material weighs more, so a ton of it covers less.
To run your own numbers, use the volume and tonnage calculator.
When to choose pea gravel
Best suited to:
- Patios, walkways and dog runs
- Play areas with proper depth and edging
- Drainage around foundations when sized properly
Poor fit for:
- Driveways and steep paths, where it rolls and ruts
- Under pavers as a base
- Areas without edging
Quick reference numbers
- Per inch over 100 sq ft: about 0.43 tons of pea gravel (0.31 cubic yards).
- Per inch over 1,000 sq ft: about 4.3 tons.
- Another size for comparison: a 15x30 area at 4 inches takes about 7.8 tons.
- Weight used here: about 1.4 tons per cubic yard.
Common estimating mistakes
- Measuring only the main rectangle. Aprons, turnouts and curved edges add real square footage.
- Ordering exactly the math. Uneven ground and spillage nearly always need a little more than the flat calculation.
- Forgetting that compaction shrinks loose material. A loose 4-inch spread of a dense-graded stone may finish closer to 3 inches after rolling.
- Ignoring the base. A thin surface layer over soft soil fails early no matter how much material is on top.
Questions people ask
How many cubic yards is 6 tons of pea gravel?
About 4.3 cubic yards at 1.4 tons per yard.
How many square feet does 6 tons of pea gravel cover at 3 inches?
About 463 square feet.
How many square feet does 6 tons cover at 2 inches?
About 694 square feet.
How much does a yard of pea gravel weigh?
About 1.3 to 1.5 tons.
Will 6 tons fit in one truck?
It depends on the truck. Single-axle dump trucks often carry under 10 tons and tandems around 13 to 16; your supplier will know their limits.
Related guides
- How Much Does a Ton of Gravel Cover? Depth Chart
- Tons to Cubic Yards for Gravel: Conversion Chart
- How Many Tons of Gravel in a Dump Truck? Loads and Coverage
- How Much Does 4 Tons of Pea Gravel Cover?
- How Much Does 5 Tons of Pea Gravel Cover?
As an Amazon Associate, AsphaltTons.com earns from qualifying purchases. Product links below are sponsored.