How Much Does 6 Tons of River Rock Cover?
How much does 6 tons of river rock cover depends on how deep you spread it. At about 1.35 tons per cubic yard, 6 tons is roughly 4.4 cubic yards. Spread 3 inches deep, that covers about 480 square feet. Halve the depth and you roughly double the area.
Volume and tonnage calculator →How the coverage is figured
- Tons to cubic yards: 6 ÷ 1.35 = 4.4 yd³.
- Cubic yards to cubic feet: × 27 = 120 cu ft.
- Divide by depth in feet: at 3 inches (0.250 ft), 120 ÷ 0.250 = 480 sq ft.
Coverage of 6 tons at different depths
| Depth | Square feet covered | Square yards |
|---|---|---|
| 2 in | 720 | 80 |
| 3 in | 480 | 53 |
| 4 in | 360 | 40 |
About river rock
River rock is mostly decorative and for drainage beds. It is not meant to be driven on and tends to roll if used as a walking surface. Weight runs about 1.25 to 1.45 tons per cubic yard, so treat the table as a planning range rather than an exact figure.
Planning around 6 tons
6 tons is a light load that a single-axle dump truck can often handle, though legal limits vary by truck and state. Spread from the pile with a loader, skid steer or wheelbarrow, then rake to depth before compacting if the material calls for it.
- Check depth as you go. Stakes marked at the target depth help keep the spread even.
- Expect some loss. Compaction and uneven ground use more than the flat-math figure. Keep about 10 percent in reserve.
- Ask about moisture. Wet material weighs more, so a ton of it covers less.
To run your own numbers, use the volume and tonnage calculator.
When to choose river rock
Best suited to:
- Dry creek beds and drainage swales
- Decorative borders and planting beds
- Around downspouts to stop splash erosion
Poor fit for:
- Walking surfaces
- Driveways
- Bases under slabs or pavers
Quick reference numbers
- Per inch over 100 sq ft: about 0.42 tons of river rock (0.31 cubic yards).
- Per inch over 1,000 sq ft: about 4.2 tons.
- Another size for comparison: a 15x30 area at 4 inches takes about 7.5 tons.
- Weight used here: about 1.35 tons per cubic yard.
Mistakes that throw off the order
- Ignoring the base. A thin surface layer over soft soil fails early no matter how much material is on top.
- Measuring only the main rectangle. Aprons, turnouts and curved edges add real square footage.
- Ordering exactly the math. Uneven ground and spillage nearly always need a little more than the flat calculation.
- Forgetting that compaction shrinks loose material. A loose 4-inch spread of a dense-graded stone may finish closer to 3 inches after rolling.
Questions people ask
How many cubic yards is 6 tons of river rock?
About 4.4 cubic yards at 1.35 tons per yard.
How many square feet does 6 tons of river rock cover at 3 inches?
About 480 square feet.
How many square feet does 6 tons cover at 2 inches?
About 720 square feet.
How much does a yard of river rock weigh?
About 1.25 to 1.45 tons.
Will 6 tons fit in one truck?
It depends on the truck. Single-axle dump trucks often carry under 10 tons and tandems around 13 to 16; your supplier will know their limits.
Related guides
- How Much Does a Ton of River Rock Cover?
- Tons to Cubic Yards for Gravel: Conversion Chart
- How Many Tons of Gravel in a Dump Truck? Loads and Coverage
- How Much Does 4 Tons of River Rock Cover?
- How Much Does 5 Tons of River Rock Cover?
As an Amazon Associate, AsphaltTons.com earns from qualifying purchases. Product links below are sponsored.