How Much Does 8 Tons of Gravel Cover?
How much does 8 tons of gravel cover depends on how deep you spread it. At about 1.4 tons per cubic yard, 8 tons is roughly 5.7 cubic yards. Spread 4 inches deep, that covers about 463 square feet. Halve the depth and you roughly double the area.
Volume and tonnage calculator →How the coverage is figured
- Tons to cubic yards: 8 ÷ 1.4 = 5.7 yd³.
- Cubic yards to cubic feet: × 27 = 154 cu ft.
- Divide by depth in feet: at 4 inches (0.333 ft), 154 ÷ 0.333 = 463 sq ft.
Coverage of 8 tons at different depths
| Depth | Square feet covered | Square yards |
|---|---|---|
| 2 in | 926 | 103 |
| 3 in | 617 | 69 |
| 4 in | 463 | 51 |
| 6 in | 309 | 34 |
About gravel
Plain gravel is a loose term. Yards use it for rounded bank or river stone as well as for crushed rock, so ask whether the load is washed, crushed or a mix before you lock in a tonnage. Weight runs about 1.3 to 1.5 tons per cubic yard, so treat the table as a planning range rather than an exact figure.
What 8 tons looks like on site
For delivery, 8 tons usually fits on one smaller dump truck. Ask the supplier how they will split it. Spread from the pile with a loader, skid steer or wheelbarrow, then rake to depth before compacting if the material calls for it.
- Check depth as you go. Stakes marked at the target depth help keep the spread even.
- Expect some loss. Compaction and uneven ground use more than the flat-math figure. Keep about 10 percent in reserve.
- Ask about moisture. Wet material weighs more, so a ton of it covers less.
To run your own numbers, use the volume and tonnage calculator.
Good and poor uses for gravel
Works well for:
- Rural driveways and lanes where low upfront cost matters
- Drainage areas and around downspouts
- Temporary access while a site is under construction
Poor fit for:
- Steep slopes, where loose stone washes downhill
- Spots plowed often, since plows push gravel into the lawn
- Areas next to doors, because stone tracks inside
Quick reference numbers
- Per inch over 100 sq ft: about 0.43 tons of gravel (0.31 cubic yards).
- Per inch over 1,000 sq ft: about 4.3 tons.
- Another size for comparison: a 14x28 area at 2 inches takes about 3.4 tons.
- Weight used here: about 1.4 tons per cubic yard.
Common estimating mistakes
- Assuming every supplier uses the same weight. Two yards selling the same product name can quote different tons per yard.
- Skipping drainage. Water sitting under any surface softens the base and leads to ruts and potholes.
- Using inches as if they were feet. Depth has to be divided by 12 before you multiply; skipping that step inflates the order twelvefold.
- Ignoring the base. A thin surface layer over soft soil fails early no matter how much material is on top.
Questions people ask
How many cubic yards is 8 tons of gravel?
About 5.7 cubic yards at 1.4 tons per yard.
How many square feet does 8 tons of gravel cover at 4 inches?
About 463 square feet.
How many square feet does 8 tons cover at 2 inches?
About 926 square feet.
How much does a yard of gravel weigh?
About 1.3 to 1.5 tons.
Will 8 tons fit in one truck?
It depends on the truck. Single-axle dump trucks often carry under 10 tons and tandems around 13 to 16; your supplier will know their limits.
Related guides
- How Much Does a Ton of Gravel Cover? Depth Chart
- Tons to Cubic Yards for Gravel: Conversion Chart
- How Many Tons of Gravel in a Dump Truck? Loads and Coverage
- How Much Does 6 Tons of Gravel Cover?
- How Much Does 7 Tons of Gravel Cover?
As an Amazon Associate, AsphaltTons.com earns from qualifying purchases. Product links below are sponsored.