How Much Gravel for 300 Square Feet?
How much gravel for 300 square feet depends on depth. At 4 inches you need about 3.70 cubic yards, roughly 5.2 tons at 1.4 tons per yard. Going to 6 inches raises it to 7.8 tons.
Volume and tonnage calculator →Gravel for 300 sq ft by depth
| Depth | Cubic yards | Tons | Tons +10% |
|---|---|---|---|
| 2 in | 1.85 | 2.6 | 2.9 |
| 3 in | 2.78 | 3.9 | 4.3 |
| 4 in | 3.70 | 5.2 | 5.7 |
| 6 in | 5.56 | 7.8 | 8.6 |
Working it out
- 300 sq ft × (4 ÷ 12) ft = 100.0 cubic feet.
- ÷ 27 = 3.70 cubic yards.
- × 1.4 tons per yard = 5.2 tons.
About gravel
Because ’gravel’ covers so many products, the weight per yard moves with stone size and how much fine material is in the pile. Rounded stone with no fines rolls under tires; crushed stone with fines locks together. Typical weight: 1.3 to 1.5 tons per cubic yard.
Getting the order right
- Measure odd shapes in pieces. Split curves and L-shapes into rectangles and add them.
- Add a margin. About 10 percent covers compaction and low spots.
- Bulk or bags. Bulk delivery is the practical choice here.
- Prep first. Remove sod, compact the subgrade and set edging before the stone arrives.
Use the volume and tonnage calculator for any other size.
Where gravel fits
Best suited to:
- Rural driveways and lanes where low upfront cost matters
- Drainage areas and around downspouts
- Temporary access while a site is under construction
Think twice for:
- Steep slopes, where loose stone washes downhill
- Spots plowed often, since plows push gravel into the lawn
- Areas next to doors, because stone tracks inside
Quick reference numbers
- Per inch over 100 sq ft: about 0.43 tons of gravel (0.31 cubic yards).
- Per inch over 1,000 sq ft: about 4.3 tons.
- Another size for comparison: a 12x24 area at 3 inches takes about 3.7 tons.
- Weight used here: about 1.4 tons per cubic yard.
Common estimating mistakes
- Measuring only the main rectangle. Aprons, turnouts and curved edges add real square footage.
- Forgetting that compaction shrinks loose material. A loose 4-inch spread of a dense-graded stone may finish closer to 3 inches after rolling.
- Ordering exactly the math. Uneven ground and spillage nearly always need a little more than the flat calculation.
- Assuming every supplier uses the same weight. Two yards selling the same product name can quote different tons per yard.
Questions people ask
How many tons of gravel for 300 square feet?
About 5.2 tons at 4 inches deep.
How many cubic yards of gravel for 300 square feet?
About 3.70 yards at 4 inches.
How much gravel for 300 square feet at 2 inches?
About 2.6 tons, or 1.85 cubic yards.
How much does a yard of gravel weigh?
About 1.3 to 1.5 tons.
Should I add extra?
Yes, about 10 percent is a common allowance.
Related guides
- How Much Does a Ton of Gravel Cover? Depth Chart
- Tons to Cubic Yards for Gravel: Conversion Chart
- How Much Does a Ton of Gravel Cover? Depth Chart
- How Much Gravel for 200 Square Feet?
- How Much Gravel for 250 Square Feet?
As an Amazon Associate, AsphaltTons.com earns from qualifying purchases. Product links below are sponsored.