How Much Gravel for a 10x75 Driveway?
How much gravel for a 10x75 driveway is a quick volume problem. 750 square feet at 4 inches comes to 9.26 cubic yards. Gravel usually weighs about 1.3 to 1.5 tons per cubic yard, so plan on roughly 13.0 tons.
Volume and tonnage calculator →The math for a 10x75 driveway
- Area: 10 × 75 = 750 sq ft.
- Depth in feet: 4 ÷ 12 = 0.333 ft.
- Cubic feet: 750 × 0.333 = 250.0 cu ft.
- Cubic yards: ÷ 27 = 9.26 yd³.
- Tons: × 1.4 = 13.0 tons.
The volume and tonnage calculator does this for any size.
Gravel needed by depth
| Depth | Cubic yards | Tons (approx.) | Tons +10% |
|---|---|---|---|
| 2 in | 4.63 | 6.5 | 7.1 |
| 3 in | 6.94 | 9.7 | 10.7 |
| 4 in | 9.26 | 13.0 | 14.3 |
| 6 in | 13.89 | 19.4 | 21.4 |
About gravel
Plain gravel is a loose term. Yards use it for rounded bank or river stone as well as for crushed rock, so ask whether the load is washed, crushed or a mix before you lock in a tonnage. If the yard sells by the cubic yard instead of the ton, use the cubic-yard column directly.
Preparing the driveway
Strip sod and soft topsoil, grade for drainage and compact the subgrade before any stone goes down. Gravel drives last longer with a compacted base layer under the top stone and a slight crown so water runs off. For car and truck traffic, the depths in the table above are a reasonable starting range.
Ordering tips
- Round up. Compaction and uneven ground eat material. Adding about 10 percent is common.
- Delivery size. 14.3 tons may take more than one typical dump truck load; small loads may carry a delivery fee. See how many tons of gravel in a dump truck.
- Bulk vs bags. At this size bulk delivery is usually the practical choice.
- Where it drops. Have the truck dump as close to the driveway as firm ground allows.
Where gravel fits
Good uses:
- Rural driveways and lanes where low upfront cost matters
- Drainage areas and around downspouts
- Temporary access while a site is under construction
Think twice for:
- Steep slopes, where loose stone washes downhill
- Spots plowed often, since plows push gravel into the lawn
- Areas next to doors, because stone tracks inside
Quick reference numbers
- Per inch over 100 sq ft: about 0.43 tons of gravel (0.31 cubic yards).
- Per inch over 1,000 sq ft: about 4.3 tons.
- Another size for comparison: a 15x30 area at 4 inches takes about 7.8 tons.
- Weight used here: about 1.4 tons per cubic yard.
Common estimating mistakes
- Ignoring the base. A thin surface layer over soft soil fails early no matter how much material is on top.
- Mixing up cubic yards and tons. Yards are volume, tons are weight; convert with the product’s weight per yard.
- Using inches as if they were feet. Depth has to be divided by 12 before you multiply; skipping that step inflates the order twelvefold.
- Forgetting that compaction shrinks loose material. A loose 4-inch spread of a dense-graded stone may finish closer to 3 inches after rolling.
Questions people ask
How many tons of gravel for a 10x75 driveway?
About 13.0 tons at 4 inches deep, or 14.3 tons with 10 percent extra.
How many cubic yards is a 10x75 driveway at 4 inches?
About 9.26 cubic yards.
How much does a cubic yard of gravel weigh?
Usually around 1.3 to 1.5 tons, depending on stone size, fines and moisture.
How deep should gravel be for a driveway?
The table above shows 2 to 6 inches. Shallower depths suit top dressing; deeper depths suit new installs and heavier use.
How many square feet is 10x75?
750 square feet.
Related guides
- How Much Does a Ton of Gravel Cover? Depth Chart
- Tons to Cubic Yards for Gravel: Conversion Chart
- How Many Tons of Gravel in a Dump Truck? Loads and Coverage
- How Much Gravel for a 10x60 Driveway?
- How Much Gravel for a 10x70 Driveway?
As an Amazon Associate, AsphaltTons.com earns from qualifying purchases. Product links below are sponsored.