How Much Gravel for a 14x70 Driveway?
How much gravel for a 14x70 driveway: at 4 inches deep you need about 12.10 cubic yards, which is roughly 16.9 tons at 1.4 tons per yard. The driveway covers 980 square feet, so every inch of depth adds about 3.02 yards.
Volume and tonnage calculator →The math for a 14x70 driveway
- Area: 14 × 70 = 980 sq ft.
- Depth in feet: 4 ÷ 12 = 0.333 ft.
- Cubic feet: 980 × 0.333 = 326.7 cu ft.
- Cubic yards: ÷ 27 = 12.10 yd³.
- Tons: × 1.4 = 16.9 tons.
The volume and tonnage calculator does this for any size.
Gravel needed by depth
| Depth | Cubic yards | Tons (approx.) | Tons +10% |
|---|---|---|---|
| 2 in | 6.05 | 8.5 | 9.3 |
| 3 in | 9.07 | 12.7 | 14.0 |
| 4 in | 12.10 | 16.9 | 18.6 |
| 6 in | 18.15 | 25.4 | 27.9 |
About gravel
Plain gravel is a loose term. Yards use it for rounded bank or river stone as well as for crushed rock, so ask whether the load is washed, crushed or a mix before you lock in a tonnage. Weight per yard is a planning number; the scale ticket at the yard is the real one.
Preparing the driveway
Strip sod and soft topsoil, grade for drainage and compact the subgrade before any stone goes down. Gravel drives last longer with a compacted base layer under the top stone and a slight crown so water runs off. Since the driveway carries car and truck traffic, a little extra depth is cheap insurance.
Ordering tips
- Round up. Compaction and uneven ground eat material. Adding about 10 percent is common.
- Delivery size. 18.6 tons may take more than one typical dump truck load; small loads may carry a delivery fee. See how many tons of gravel in a dump truck.
- Bulk vs bags. At this size bulk delivery is usually the practical choice.
- Where it drops. Have the truck dump as close to the driveway as firm ground allows.
Where gravel fits
Best suited to:
- Rural driveways and lanes where low upfront cost matters
- Drainage areas and around downspouts
- Temporary access while a site is under construction
Think twice for:
- Steep slopes, where loose stone washes downhill
- Spots plowed often, since plows push gravel into the lawn
- Areas next to doors, because stone tracks inside
Quick reference numbers
- Per inch over 100 sq ft: about 0.43 tons of gravel (0.31 cubic yards).
- Per inch over 1,000 sq ft: about 4.3 tons.
- Another size for comparison: a 12x24 area at 2 inches takes about 2.5 tons.
- Weight used here: about 1.4 tons per cubic yard.
Mistakes that throw off the order
- Using inches as if they were feet. Depth has to be divided by 12 before you multiply; skipping that step inflates the order twelvefold.
- Forgetting that compaction shrinks loose material. A loose 4-inch spread of a dense-graded stone may finish closer to 3 inches after rolling.
- Mixing up cubic yards and tons. Yards are volume, tons are weight; convert with the product’s weight per yard.
- Skipping drainage. Water sitting under any surface softens the base and leads to ruts and potholes.
Questions people ask
How many tons of gravel for a 14x70 driveway?
About 16.9 tons at 4 inches deep, or 18.6 tons with 10 percent extra.
How many cubic yards is a 14x70 driveway at 4 inches?
About 12.10 cubic yards.
How much does a cubic yard of gravel weigh?
Usually around 1.3 to 1.5 tons, depending on stone size, fines and moisture.
How deep should gravel be for a driveway?
The table above shows 2 to 6 inches. Shallower depths suit top dressing; deeper depths suit new installs and heavier use.
How many square feet is 14x70?
980 square feet.
Related guides
- How Much Does a Ton of Gravel Cover? Depth Chart
- Tons to Cubic Yards for Gravel: Conversion Chart
- How Many Tons of Gravel in a Dump Truck? Loads and Coverage
- How Much Gravel for a 14x50 Driveway?
- How Much Gravel for a 14x60 Driveway?
As an Amazon Associate, AsphaltTons.com earns from qualifying purchases. Product links below are sponsored.