How Much Gravel for a 30x40 Parking Pad?
How much gravel for a 30x40 parking pad is a quick volume problem. 1,200 square feet at 4 inches comes to 14.81 cubic yards. Gravel usually weighs about 1.3 to 1.5 tons per cubic yard, so plan on roughly 20.7 tons.
Volume and tonnage calculator →The math for a 30x40 parking pad
- Area: 30 × 40 = 1,200 sq ft.
- Depth in feet: 4 ÷ 12 = 0.333 ft.
- Cubic feet: 1,200 × 0.333 = 400.0 cu ft.
- Cubic yards: ÷ 27 = 14.81 yd³.
- Tons: × 1.4 = 20.7 tons.
The volume and tonnage calculator does this for any size.
Gravel needed by depth
| Depth | Cubic yards | Tons (approx.) | Tons +10% |
|---|---|---|---|
| 2 in | 7.41 | 10.4 | 11.4 |
| 3 in | 11.11 | 15.6 | 17.1 |
| 4 in | 14.81 | 20.7 | 22.8 |
| 6 in | 22.22 | 31.1 | 34.2 |
About gravel
Because ’gravel’ covers so many products, the weight per yard moves with stone size and how much fine material is in the pile. Rounded stone with no fines rolls under tires; crushed stone with fines locks together. If the yard sells by the cubic yard instead of the ton, use the cubic-yard column directly.
Preparing the parking pad
Dig out organic soil, compact the subgrade and set an edge so the stone does not migrate onto the lawn. A pad that holds parked weight for long periods benefits from a dense base under the surface stone. This parking pad sees parked vehicles, so match the depth to that load rather than to the minimum.
Ordering tips
- Round up. Compaction and uneven ground eat material. Adding about 10 percent is common.
- Delivery size. 22.8 tons may take more than one typical dump truck load; small loads may carry a delivery fee. See how many tons of gravel in a dump truck.
- Bulk vs bags. At this size bulk delivery is usually the practical choice.
- Where it drops. Have the truck dump as close to the parking pad as firm ground allows.
When to choose gravel
Works well for:
- Rural driveways and lanes where low upfront cost matters
- Drainage areas and around downspouts
- Temporary access while a site is under construction
Think twice for:
- Steep slopes, where loose stone washes downhill
- Spots plowed often, since plows push gravel into the lawn
- Areas next to doors, because stone tracks inside
Quick reference numbers
- Per inch over 100 sq ft: about 0.43 tons of gravel (0.31 cubic yards).
- Per inch over 1,000 sq ft: about 4.3 tons.
- Another size for comparison: a 8x16 area at 3 inches takes about 1.7 tons.
- Weight used here: about 1.4 tons per cubic yard.
Where estimates go wrong
- Ordering exactly the math. Uneven ground and spillage nearly always need a little more than the flat calculation.
- Mixing up cubic yards and tons. Yards are volume, tons are weight; convert with the product’s weight per yard.
- Skipping drainage. Water sitting under any surface softens the base and leads to ruts and potholes.
- Ignoring the base. A thin surface layer over soft soil fails early no matter how much material is on top.
Questions people ask
How many tons of gravel for a 30x40 parking pad?
About 20.7 tons at 4 inches deep, or 22.8 tons with 10 percent extra.
How many cubic yards is a 30x40 parking pad at 4 inches?
About 14.81 cubic yards.
How much does a cubic yard of gravel weigh?
Usually around 1.3 to 1.5 tons, depending on stone size, fines and moisture.
How deep should gravel be for a parking pad?
The table above shows 2 to 6 inches. Shallower depths suit top dressing; deeper depths suit new installs and heavier use.
How many square feet is 30x40?
1,200 square feet.
Related guides
- How Much Does a Ton of Gravel Cover? Depth Chart
- Tons to Cubic Yards for Gravel: Conversion Chart
- How Many Tons of Gravel in a Dump Truck? Loads and Coverage
- How Much Gravel for a 30x30 Parking Pad?
- How Much Gravel for a 30x36 Parking Pad?
As an Amazon Associate, AsphaltTons.com earns from qualifying purchases. Product links below are sponsored.