How Much Gravel for a 6x10 Walkway?
A 6 by 10 foot walkway is 60 square feet. How much gravel for a 6x10 walkway depends on depth: at 3 inches it is about 0.56 cubic yards or 0.8 tons. Suppliers usually sell by the ton, so the tonnage is the number to give them.
Volume and tonnage calculator →The math for a 6x10 walkway
- Area: 6 × 10 = 60 sq ft.
- Depth in feet: 3 ÷ 12 = 0.250 ft.
- Cubic feet: 60 × 0.250 = 15.0 cu ft.
- Cubic yards: ÷ 27 = 0.56 yd³.
- Tons: × 1.4 = 0.8 tons.
The volume and tonnage calculator does this for any size.
Gravel needed by depth
| Depth | Cubic yards | Tons (approx.) | Tons +10% |
|---|---|---|---|
| 2 in | 0.37 | 0.5 | 0.6 |
| 3 in | 0.56 | 0.8 | 0.9 |
| 4 in | 0.74 | 1.0 | 1.1 |
| 6 in | 1.11 | 1.6 | 1.7 |
About gravel
Plain gravel is a loose term. Yards use it for rounded bank or river stone as well as for crushed rock, so ask whether the load is washed, crushed or a mix before you lock in a tonnage. Ask your supplier for their own tons-per-yard figure, since stone source and moisture shift it.
Preparing the walkway
Dig the path a few inches below grade, compact the bottom, add fabric if needed and install edging on both sides so the material stays on the walk. Since the walkway carries foot traffic, a little extra depth is cheap insurance.
Ordering tips
- Round up. Compaction and uneven ground eat material. Adding about 10 percent is common.
- Delivery size. 0.9 tons fits in a single typical dump truck load; small loads may carry a delivery fee. See how many tons of gravel in a dump truck.
- Bulk vs bags. At about 0.8 tons this job is small enough that bagged material could work; a 0.5 cubic foot bag holds about 1/54 of a yard, so compare the bag count with a bulk minimum.
- Where it drops. Have the truck dump as close to the walkway as firm ground allows.
Where gravel fits
Best suited to:
- Rural driveways and lanes where low upfront cost matters
- Drainage areas and around downspouts
- Temporary access while a site is under construction
Less suited to:
- Steep slopes, where loose stone washes downhill
- Spots plowed often, since plows push gravel into the lawn
- Areas next to doors, because stone tracks inside
Quick reference numbers
- Per inch over 100 sq ft: about 0.43 tons of gravel (0.31 cubic yards).
- Per inch over 1,000 sq ft: about 4.3 tons.
- Another size for comparison: a 8x16 area at 4 inches takes about 2.2 tons.
- Weight used here: about 1.4 tons per cubic yard.
Where estimates go wrong
- Ordering exactly the math. Uneven ground and spillage nearly always need a little more than the flat calculation.
- Measuring only the main rectangle. Aprons, turnouts and curved edges add real square footage.
- Skipping drainage. Water sitting under any surface softens the base and leads to ruts and potholes.
- Assuming every supplier uses the same weight. Two yards selling the same product name can quote different tons per yard.
Questions people ask
How many tons of gravel for a 6x10 walkway?
About 0.8 tons at 3 inches deep, or 0.9 tons with 10 percent extra.
How many cubic yards is a 6x10 walkway at 3 inches?
About 0.56 cubic yards.
How much does a cubic yard of gravel weigh?
Usually around 1.3 to 1.5 tons, depending on stone size, fines and moisture.
How deep should gravel be for a walkway?
The table above shows 2 to 6 inches. Shallower depths suit top dressing; deeper depths suit new installs and heavier use.
How many square feet is 6x10?
60 square feet.
Related guides
- How Much Does a Ton of Gravel Cover? Depth Chart
- Tons to Cubic Yards for Gravel: Conversion Chart
- How Many Tons of Gravel in a Dump Truck? Loads and Coverage
- How Much Gravel for a 5x75 Walkway?
- How Much Gravel for a 5x100 Walkway?
As an Amazon Associate, AsphaltTons.com earns from qualifying purchases. Product links below are sponsored.