How Much Limestone Screenings for a 16x12 Patio?
How much limestone screenings for a 16x12 patio: at 3 inches deep you need about 1.78 cubic yards, which is roughly 2.5 tons at 1.4 tons per yard. The patio covers 192 square feet, so every inch of depth adds about 0.59 yards.
Volume and tonnage calculator →The math for a 16x12 patio
- Area: 16 × 12 = 192 sq ft.
- Depth in feet: 3 ÷ 12 = 0.250 ft.
- Cubic feet: 192 × 0.250 = 48.0 cu ft.
- Cubic yards: ÷ 27 = 1.78 yd³.
- Tons: × 1.4 = 2.5 tons.
The volume and tonnage calculator does this for any size.
Limestone screenings needed by depth
| Depth | Cubic yards | Tons (approx.) | Tons +10% |
|---|---|---|---|
| 1 in | 0.59 | 0.8 | 0.9 |
| 2 in | 1.19 | 1.7 | 1.8 |
| 3 in | 1.78 | 2.5 | 2.7 |
About limestone screenings
Screenings hold moisture and can crust over. Use them in thin layers over a compacted stone base instead of as a thick layer on their own. If the yard sells by the cubic yard instead of the ton, use the cubic-yard column directly.
Preparing the patio
Remove sod, level the area with a slight slope away from the house, and lay landscape fabric if weeds are a concern. Edging keeps loose material inside the patio footprint. For foot traffic and furniture, the depths in the table above are a reasonable starting range.
Ordering tips
- Round up. Compaction and uneven ground eat material. Adding about 10 percent is common.
- Delivery size. 2.7 tons fits in a single typical dump truck load; small loads may carry a delivery fee. See how many tons of gravel in a dump truck.
- Bulk vs bags. At this size bulk delivery is usually the practical choice.
- Where it drops. Have the truck dump as close to the patio as firm ground allows.
When to choose limestone screenings
Works well for:
- Paver and flagstone setting beds
- Firm walking paths
- Top-dressing a compacted stone base
Less suited to:
- Deep layers on their own
- Low spots that collect water
- Under heavy vehicle traffic without a base
Quick reference numbers
- Per inch over 100 sq ft: about 0.43 tons of limestone screenings (0.31 cubic yards).
- Per inch over 1,000 sq ft: about 4.3 tons.
- Another size for comparison: a 10x20 area at 4 inches takes about 3.5 tons.
- Weight used here: about 1.4 tons per cubic yard.
Mistakes that throw off the order
- Ordering exactly the math. Uneven ground and spillage nearly always need a little more than the flat calculation.
- Forgetting that compaction shrinks loose material. A loose 4-inch spread of a dense-graded stone may finish closer to 3 inches after rolling.
- Mixing up cubic yards and tons. Yards are volume, tons are weight; convert with the product’s weight per yard.
- Assuming every supplier uses the same weight. Two yards selling the same product name can quote different tons per yard.
Questions people ask
How many tons of limestone screenings for a 16x12 patio?
About 2.5 tons at 3 inches deep, or 2.7 tons with 10 percent extra.
How many cubic yards is a 16x12 patio at 3 inches?
About 1.78 cubic yards.
How much does a cubic yard of limestone screenings weigh?
Usually around 1.3 to 1.5 tons, depending on stone size, fines and moisture.
How deep should limestone screenings be for a patio?
The table above shows 1 to 3 inches. Shallower depths suit top dressing; deeper depths suit new installs and heavier use.
How many square feet is 16x12?
192 square feet.
Related guides
- #10 Stone (Stone Dust): Size, Uses and How Many Tons
- Tons to Cubic Yards for Gravel: Conversion Chart
- How Many Tons of Gravel in a Dump Truck? Loads and Coverage
- How Much Does a Ton of Gravel Cover? Depth Chart
- How Much Limestone Screenings for a 14x30 Patio?
- How Much Limestone Screenings for a 16x10 Patio?
As an Amazon Associate, AsphaltTons.com earns from qualifying purchases. Product links below are sponsored.