How Much Limestone Screenings for a 3x100 Walkway?
How much limestone screenings for a 3x100 walkway is a quick volume problem. 300 square feet at 3 inches comes to 2.78 cubic yards. Limestone screenings usually weighs about 1.3 to 1.5 tons per cubic yard, so plan on roughly 3.9 tons.
Volume and tonnage calculator →The math for a 3x100 walkway
- Area: 3 × 100 = 300 sq ft.
- Depth in feet: 3 ÷ 12 = 0.250 ft.
- Cubic feet: 300 × 0.250 = 75.0 cu ft.
- Cubic yards: ÷ 27 = 2.78 yd³.
- Tons: × 1.4 = 3.9 tons.
The volume and tonnage calculator does this for any size.
Limestone screenings needed by depth
| Depth | Cubic yards | Tons (approx.) | Tons +10% |
|---|---|---|---|
| 1 in | 0.93 | 1.3 | 1.4 |
| 2 in | 1.85 | 2.6 | 2.9 |
| 3 in | 2.78 | 3.9 | 4.3 |
About limestone screenings
Screenings hold moisture and can crust over. Use them in thin layers over a compacted stone base instead of as a thick layer on their own. If the yard sells by the cubic yard instead of the ton, use the cubic-yard column directly.
Preparing the walkway
Dig the path a few inches below grade, compact the bottom, add fabric if needed and install edging on both sides so the material stays on the walk. For foot traffic, the depths in the table above are a reasonable starting range.
Ordering tips
- Round up. Compaction and uneven ground eat material. Adding about 10 percent is common.
- Delivery size. 4.3 tons fits in a single typical dump truck load; small loads may carry a delivery fee. See how many tons of gravel in a dump truck.
- Bulk vs bags. At this size bulk delivery is usually the practical choice.
- Where it drops. Have the truck dump as close to the walkway as firm ground allows.
When to choose limestone screenings
Good uses:
- Paver and flagstone setting beds
- Firm walking paths
- Top-dressing a compacted stone base
Less suited to:
- Deep layers on their own
- Low spots that collect water
- Under heavy vehicle traffic without a base
Quick reference numbers
- Per inch over 100 sq ft: about 0.43 tons of limestone screenings (0.31 cubic yards).
- Per inch over 1,000 sq ft: about 4.3 tons.
- Another size for comparison: a 20x25 area at 4 inches takes about 8.6 tons.
- Weight used here: about 1.4 tons per cubic yard.
Where estimates go wrong
- Assuming every supplier uses the same weight. Two yards selling the same product name can quote different tons per yard.
- Forgetting that compaction shrinks loose material. A loose 4-inch spread of a dense-graded stone may finish closer to 3 inches after rolling.
- Ordering exactly the math. Uneven ground and spillage nearly always need a little more than the flat calculation.
- Using inches as if they were feet. Depth has to be divided by 12 before you multiply; skipping that step inflates the order twelvefold.
Questions people ask
How many tons of limestone screenings for a 3x100 walkway?
About 3.9 tons at 3 inches deep, or 4.3 tons with 10 percent extra.
How many cubic yards is a 3x100 walkway at 3 inches?
About 2.78 cubic yards.
How much does a cubic yard of limestone screenings weigh?
Usually around 1.3 to 1.5 tons, depending on stone size, fines and moisture.
How deep should limestone screenings be for a walkway?
The table above shows 1 to 3 inches. Shallower depths suit top dressing; deeper depths suit new installs and heavier use.
How many square feet is 3x100?
300 square feet.
Related guides
- #10 Stone (Stone Dust): Size, Uses and How Many Tons
- Tons to Cubic Yards for Gravel: Conversion Chart
- How Many Tons of Gravel in a Dump Truck? Loads and Coverage
- How Much Does a Ton of Gravel Cover? Depth Chart
- How Much Limestone Screenings for a 3x60 Walkway?
- How Much Limestone Screenings for a 3x75 Walkway?
As an Amazon Associate, AsphaltTons.com earns from qualifying purchases. Product links below are sponsored.