How Much Limestone Screenings for a 4x30 Walkway?
A 4 by 30 foot walkway is 120 square feet. How much limestone screenings for a 4x30 walkway depends on depth: at 3 inches it is about 1.11 cubic yards or 1.6 tons. Suppliers usually sell by the ton, so the tonnage is the number to give them.
Volume and tonnage calculator →The math for a 4x30 walkway
- Area: 4 × 30 = 120 sq ft.
- Depth in feet: 3 ÷ 12 = 0.250 ft.
- Cubic feet: 120 × 0.250 = 30.0 cu ft.
- Cubic yards: ÷ 27 = 1.11 yd³.
- Tons: × 1.4 = 1.6 tons.
The volume and tonnage calculator does this for any size.
Limestone screenings needed by depth
| Depth | Cubic yards | Tons (approx.) | Tons +10% |
|---|---|---|---|
| 1 in | 0.37 | 0.5 | 0.6 |
| 2 in | 0.74 | 1.0 | 1.1 |
| 3 in | 1.11 | 1.6 | 1.7 |
About limestone screenings
Screenings hold moisture and can crust over. Use them in thin layers over a compacted stone base instead of as a thick layer on their own. Ask your supplier for their own tons-per-yard figure, since stone source and moisture shift it.
Preparing the walkway
Dig the path a few inches below grade, compact the bottom, add fabric if needed and install edging on both sides so the material stays on the walk. This walkway sees foot traffic, so match the depth to that load rather than to the minimum.
Ordering tips
- Round up. Compaction and uneven ground eat material. Adding about 10 percent is common.
- Delivery size. 1.7 tons fits in a single typical dump truck load; small loads may carry a delivery fee. See how many tons of gravel in a dump truck.
- Bulk vs bags. At this size bulk delivery is usually the practical choice.
- Where it drops. Have the truck dump as close to the walkway as firm ground allows.
Good and poor uses for limestone screenings
Good uses:
- Paver and flagstone setting beds
- Firm walking paths
- Top-dressing a compacted stone base
Think twice for:
- Deep layers on their own
- Low spots that collect water
- Under heavy vehicle traffic without a base
Quick reference numbers
- Per inch over 100 sq ft: about 0.43 tons of limestone screenings (0.31 cubic yards).
- Per inch over 1,000 sq ft: about 4.3 tons.
- Another size for comparison: a 15x30 area at 2 inches takes about 3.9 tons.
- Weight used here: about 1.4 tons per cubic yard.
Mistakes that throw off the order
- Ignoring the base. A thin surface layer over soft soil fails early no matter how much material is on top.
- Mixing up cubic yards and tons. Yards are volume, tons are weight; convert with the product’s weight per yard.
- Forgetting that compaction shrinks loose material. A loose 4-inch spread of a dense-graded stone may finish closer to 3 inches after rolling.
- Ordering exactly the math. Uneven ground and spillage nearly always need a little more than the flat calculation.
Questions people ask
How many tons of limestone screenings for a 4x30 walkway?
About 1.6 tons at 3 inches deep, or 1.7 tons with 10 percent extra.
How many cubic yards is a 4x30 walkway at 3 inches?
About 1.11 cubic yards.
How much does a cubic yard of limestone screenings weigh?
Usually around 1.3 to 1.5 tons, depending on stone size, fines and moisture.
How deep should limestone screenings be for a walkway?
The table above shows 1 to 3 inches. Shallower depths suit top dressing; deeper depths suit new installs and heavier use.
How many square feet is 4x30?
120 square feet.
Related guides
- #10 Stone (Stone Dust): Size, Uses and How Many Tons
- Tons to Cubic Yards for Gravel: Conversion Chart
- How Many Tons of Gravel in a Dump Truck? Loads and Coverage
- How Much Does a Ton of Gravel Cover? Depth Chart
- How Much Limestone Screenings for a 4x20 Walkway?
- How Much Limestone Screenings for a 4x25 Walkway?
As an Amazon Associate, AsphaltTons.com earns from qualifying purchases. Product links below are sponsored.