How Much Limestone Screenings for a 6x15 Walkway?
How much limestone screenings for a 6x15 walkway: at 3 inches deep you need about 0.83 cubic yards, which is roughly 1.2 tons at 1.4 tons per yard. The walkway covers 90 square feet, so every inch of depth adds about 0.28 yards.
Volume and tonnage calculator →The math for a 6x15 walkway
- Area: 6 × 15 = 90 sq ft.
- Depth in feet: 3 ÷ 12 = 0.250 ft.
- Cubic feet: 90 × 0.250 = 22.5 cu ft.
- Cubic yards: ÷ 27 = 0.83 yd³.
- Tons: × 1.4 = 1.2 tons.
The volume and tonnage calculator does this for any size.
Limestone screenings needed by depth
| Depth | Cubic yards | Tons (approx.) | Tons +10% |
|---|---|---|---|
| 1 in | 0.28 | 0.4 | 0.4 |
| 2 in | 0.56 | 0.8 | 0.9 |
| 3 in | 0.83 | 1.2 | 1.3 |
About limestone screenings
Screenings hold moisture and can crust over. Use them in thin layers over a compacted stone base instead of as a thick layer on their own. Weight per yard is a planning number; the scale ticket at the yard is the real one.
Preparing the walkway
Dig the path a few inches below grade, compact the bottom, add fabric if needed and install edging on both sides so the material stays on the walk. For foot traffic, the depths in the table above are a reasonable starting range.
Ordering tips
- Round up. Compaction and uneven ground eat material. Adding about 10 percent is common.
- Delivery size. 1.3 tons fits in a single typical dump truck load; small loads may carry a delivery fee. See how many tons of gravel in a dump truck.
- Bulk vs bags. At about 1.2 tons this job is small enough that bagged material could work; a 0.5 cubic foot bag holds about 1/54 of a yard, so compare the bag count with a bulk minimum.
- Where it drops. Have the truck dump as close to the walkway as firm ground allows.
Good and poor uses for limestone screenings
Works well for:
- Paver and flagstone setting beds
- Firm walking paths
- Top-dressing a compacted stone base
Think twice for:
- Deep layers on their own
- Low spots that collect water
- Under heavy vehicle traffic without a base
Quick reference numbers
- Per inch over 100 sq ft: about 0.43 tons of limestone screenings (0.31 cubic yards).
- Per inch over 1,000 sq ft: about 4.3 tons.
- Another size for comparison: a 15x30 area at 2 inches takes about 3.9 tons.
- Weight used here: about 1.4 tons per cubic yard.
Common estimating mistakes
- Assuming every supplier uses the same weight. Two yards selling the same product name can quote different tons per yard.
- Ordering exactly the math. Uneven ground and spillage nearly always need a little more than the flat calculation.
- Measuring only the main rectangle. Aprons, turnouts and curved edges add real square footage.
- Mixing up cubic yards and tons. Yards are volume, tons are weight; convert with the product’s weight per yard.
Questions people ask
How many tons of limestone screenings for a 6x15 walkway?
About 1.2 tons at 3 inches deep, or 1.3 tons with 10 percent extra.
How many cubic yards is a 6x15 walkway at 3 inches?
About 0.83 cubic yards.
How much does a cubic yard of limestone screenings weigh?
Usually around 1.3 to 1.5 tons, depending on stone size, fines and moisture.
How deep should limestone screenings be for a walkway?
The table above shows 1 to 3 inches. Shallower depths suit top dressing; deeper depths suit new installs and heavier use.
How many square feet is 6x15?
90 square feet.
Related guides
- #10 Stone (Stone Dust): Size, Uses and How Many Tons
- Tons to Cubic Yards for Gravel: Conversion Chart
- How Many Tons of Gravel in a Dump Truck? Loads and Coverage
- How Much Does a Ton of Gravel Cover? Depth Chart
- How Much Limestone Screenings for a 5x100 Walkway?
- How Much Limestone Screenings for a 6x10 Walkway?
As an Amazon Associate, AsphaltTons.com earns from qualifying purchases. Product links below are sponsored.