How Much Pea Gravel for a 6x30 Walkway?
A 6 by 30 foot walkway is 180 square feet. How much pea gravel for a 6x30 walkway depends on depth: at 3 inches it is about 1.67 cubic yards or 2.3 tons. Suppliers usually sell by the ton, so the tonnage is the number to give them.
Volume and tonnage calculator →The math for a 6x30 walkway
- Area: 6 × 30 = 180 sq ft.
- Depth in feet: 3 ÷ 12 = 0.250 ft.
- Cubic feet: 180 × 0.250 = 45.0 cu ft.
- Cubic yards: ÷ 27 = 1.67 yd³.
- Tons: × 1.4 = 2.3 tons.
The volume and tonnage calculator does this for any size.
Pea gravel needed by depth
| Depth | Cubic yards | Tons (approx.) | Tons +10% |
|---|---|---|---|
| 2 in | 1.11 | 1.6 | 1.7 |
| 3 in | 1.67 | 2.3 | 2.6 |
| 4 in | 2.22 | 3.1 | 3.4 |
About pea gravel
Because pea gravel is round, it never fully locks. Keep depths modest on walkways and patios so it does not feel like walking on a beach, and use edging. Weight per yard is a planning number; the scale ticket at the yard is the real one.
Preparing the walkway
Dig the path a few inches below grade, compact the bottom, add fabric if needed and install edging on both sides so the material stays on the walk. For foot traffic, the depths in the table above are a reasonable starting range.
Ordering tips
- Round up. Compaction and uneven ground eat material. Adding about 10 percent is common.
- Delivery size. 2.6 tons fits in a single typical dump truck load; small loads may carry a delivery fee. See how many tons of gravel in a dump truck.
- Bulk vs bags. At this size bulk delivery is usually the practical choice.
- Where it drops. Have the truck dump as close to the walkway as firm ground allows.
When to choose pea gravel
Works well for:
- Patios, walkways and dog runs
- Play areas with proper depth and edging
- Drainage around foundations when sized properly
Poor fit for:
- Driveways and steep paths, where it rolls and ruts
- Under pavers as a base
- Areas without edging
Quick reference numbers
- Per inch over 100 sq ft: about 0.43 tons of pea gravel (0.31 cubic yards).
- Per inch over 1,000 sq ft: about 4.3 tons.
- Another size for comparison: a 20x25 area at 4 inches takes about 8.6 tons.
- Weight used here: about 1.4 tons per cubic yard.
Common estimating mistakes
- Skipping drainage. Water sitting under any surface softens the base and leads to ruts and potholes.
- Mixing up cubic yards and tons. Yards are volume, tons are weight; convert with the product’s weight per yard.
- Measuring only the main rectangle. Aprons, turnouts and curved edges add real square footage.
- Ignoring the base. A thin surface layer over soft soil fails early no matter how much material is on top.
Questions people ask
How many tons of pea gravel for a 6x30 walkway?
About 2.3 tons at 3 inches deep, or 2.6 tons with 10 percent extra.
How many cubic yards is a 6x30 walkway at 3 inches?
About 1.67 cubic yards.
How much does a cubic yard of pea gravel weigh?
Usually around 1.3 to 1.5 tons, depending on stone size, fines and moisture.
How deep should pea gravel be for a walkway?
The table above shows 2 to 4 inches. Shallower depths suit top dressing; deeper depths suit new installs and heavier use.
How many square feet is 6x30?
180 square feet.
Related guides
- How Much Does a Ton of Gravel Cover? Depth Chart
- Tons to Cubic Yards for Gravel: Conversion Chart
- How Many Tons of Gravel in a Dump Truck? Loads and Coverage
- How Much Pea Gravel for a 6x20 Walkway?
- How Much Pea Gravel for a 6x25 Walkway?
As an Amazon Associate, AsphaltTons.com earns from qualifying purchases. Product links below are sponsored.