How Much Pea Gravel for a 6x75 Walkway?
A 6 by 75 foot walkway is 450 square feet. How much pea gravel for a 6x75 walkway depends on depth: at 3 inches it is about 4.17 cubic yards or 5.8 tons. Suppliers usually sell by the ton, so the tonnage is the number to give them.
Volume and tonnage calculator →The math for a 6x75 walkway
- Area: 6 × 75 = 450 sq ft.
- Depth in feet: 3 ÷ 12 = 0.250 ft.
- Cubic feet: 450 × 0.250 = 112.5 cu ft.
- Cubic yards: ÷ 27 = 4.17 yd³.
- Tons: × 1.4 = 5.8 tons.
The volume and tonnage calculator does this for any size.
Pea gravel needed by depth
| Depth | Cubic yards | Tons (approx.) | Tons +10% |
|---|---|---|---|
| 2 in | 2.78 | 3.9 | 4.3 |
| 3 in | 4.17 | 5.8 | 6.4 |
| 4 in | 5.56 | 7.8 | 8.6 |
About pea gravel
Because pea gravel is round, it never fully locks. Keep depths modest on walkways and patios so it does not feel like walking on a beach, and use edging. Ask your supplier for their own tons-per-yard figure, since stone source and moisture shift it.
Preparing the walkway
Dig the path a few inches below grade, compact the bottom, add fabric if needed and install edging on both sides so the material stays on the walk. Since the walkway carries foot traffic, a little extra depth is cheap insurance.
Ordering tips
- Round up. Compaction and uneven ground eat material. Adding about 10 percent is common.
- Delivery size. 6.4 tons fits in a single typical dump truck load; small loads may carry a delivery fee. See how many tons of gravel in a dump truck.
- Bulk vs bags. At this size bulk delivery is usually the practical choice.
- Where it drops. Have the truck dump as close to the walkway as firm ground allows.
Good and poor uses for pea gravel
Best suited to:
- Patios, walkways and dog runs
- Play areas with proper depth and edging
- Drainage around foundations when sized properly
Poor fit for:
- Driveways and steep paths, where it rolls and ruts
- Under pavers as a base
- Areas without edging
Quick reference numbers
- Per inch over 100 sq ft: about 0.43 tons of pea gravel (0.31 cubic yards).
- Per inch over 1,000 sq ft: about 4.3 tons.
- Another size for comparison: a 10x20 area at 4 inches takes about 3.5 tons.
- Weight used here: about 1.4 tons per cubic yard.
Where estimates go wrong
- Ignoring the base. A thin surface layer over soft soil fails early no matter how much material is on top.
- Mixing up cubic yards and tons. Yards are volume, tons are weight; convert with the product’s weight per yard.
- Assuming every supplier uses the same weight. Two yards selling the same product name can quote different tons per yard.
- Forgetting that compaction shrinks loose material. A loose 4-inch spread of a dense-graded stone may finish closer to 3 inches after rolling.
Questions people ask
How many tons of pea gravel for a 6x75 walkway?
About 5.8 tons at 3 inches deep, or 6.4 tons with 10 percent extra.
How many cubic yards is a 6x75 walkway at 3 inches?
About 4.17 cubic yards.
How much does a cubic yard of pea gravel weigh?
Usually around 1.3 to 1.5 tons, depending on stone size, fines and moisture.
How deep should pea gravel be for a walkway?
The table above shows 2 to 4 inches. Shallower depths suit top dressing; deeper depths suit new installs and heavier use.
How many square feet is 6x75?
450 square feet.
Related guides
- How Much Does a Ton of Gravel Cover? Depth Chart
- Tons to Cubic Yards for Gravel: Conversion Chart
- How Many Tons of Gravel in a Dump Truck? Loads and Coverage
- How Much Pea Gravel for a 6x50 Walkway?
- How Much Pea Gravel for a 6x60 Walkway?
As an Amazon Associate, AsphaltTons.com earns from qualifying purchases. Product links below are sponsored.